diy solar

diy solar

Recent content by AussieSim

  1. A

    13.3kW PV Solar Hyundai + 35.5 kWh Pylontech H2 + Goodwe 11kW 3 phase hybrid inverter.

    Hello, This is an in progress install thread of my solar install, mainly because I can't find any reviews or Pylontech PowerCube H2 installations online. This install is a professional grid tied system performed by a solar installer, with electrician certification, feed in tariff and STC...
  2. A

    Need help! 48 volt caught fire

    48V is a life threatening voltage if wired incorrectly. You might be wiser to start at 24V, with safety glasses and gloves. Make sure there is no bare metal, cover busbars and terminals in Kapton tape. Use insulated tools. Use appripriate fuses and safety switches. I would also suggest you run...
  3. A

    Foshan SNAT SNADI hybrid all in one

    Mine came factory configured with HVD and LVD for the charger/inverter. They cannot be change on my unit. I forwarded Foshan SNADI the EVE280Ah datasheet with the charging parameters and asked for them to be set a little inside the max voltagr range for safety margin (I am also using a BMS)...
  4. A

    Bluecarbon UU12-150

    They're still working, my Juntek broke in 2 ways the voltage sense leads I was using melted and the shunt holding L brackets snapped. I still have an intine power meter of the type Will uses in one of his videos, but haven't retested the capacity recently. The biggest issue with this is that...
  5. A

    Using dented Lishen cells

    Sounds like they're trying to scam you
  6. A

    EVE LiFePo4 Cell Studs

    Which vendor ?
  7. A

    EcoFlow R600

    On Ecoflow's facebook page they are surveying interest in another manufacturing run of the the EF-1500 at the same kickstarter price (which was $599). Survey is still up currently. https://www.surveymonkey.com/r/BDQ5MLD Having said that a few people on their Facebook group have been able to...
  8. A

    Bought from Shenzhen Basen via Alibaba

    Are those patches applied to dents in photos 1+2 ? And a scratch to the plastic of photo 5 ?
  9. A

    Lifepo4 mishap. Can they be salvaged?

    30v = 3.75v Not good, but probably not terminal, post some pics of the bloated cells. Perhaps discharge then to 10% SOC and add compression, because the bloat on the middle they tend to splay apart at the bottom
  10. A

    Lishen 272Ah - Ah measurement way off - Help!

    https://diysolarforum.com/threads/amp-hour-measurement-and-losses-or-why-voltage-still-doesnt-matter.16508/#post-187828
  11. A

    Lishen 272AH thread?

    I'm no expert, but I believe the correct place to have put the fuse would have been at the total battery +'ve terminal Then to connect the charger to the fused terminal, like these https://www.amazon.com/Bay-Marine-Single-Terminal-included/dp/B07LC39CG5/
  12. A

    ETC 277AH Grade B?

    In that case the agent fees (can be DHL/Fedex etc) must have been negligible. The customs/duties are calculated on the Forex rate at arrival, the exchange rate is probably better than when you ordered.
  13. A

    ETC 277AH Grade B?

    $330 for the agent fees ? Or in total [Customs duties + GST + Agent fees] = $330 ? Because [$2103 AUD + 5%] + 10% = $326
  14. A

    200A Smart BMS from LLT Power

    Even the older black enclosure version ?
  15. A

    200A Smart BMS from LLT Power

    Well as long as they continue to sell the prior model which supports 8s and 16s then there's no problem. How much do Jaibaida charge per unit on Alibaba ? Do you have a link to their store ? Does their unit include the balancing leads and the bluetooth module ?
See more
Back
Top