-
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.No heating, and there is no difference in voltage between the cable ends and the inverter terminals either. Neither from one end of the...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.Here are the results: After a brief discussion with EG4 TechSolutions sTeam (above) about resistance. I included these meter readings...
-
-
JJoel Jahn replied to the thread Can I reduce idle consumption w/ second inverter?.If I have your first post question, correct? Just saying for my EG4 6000XPs they idle at 60watts. I only see that low consumption when...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.I don't know what happened to my response to this question. But yes, when shared battery is used, they seem to use an average of the two...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.Well probably the same. Do you know how it's done on the12/18k ? or who has done it for somebody. I'll look in to contacting EG4 and...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.Yes K490 I believe the calibration is off in the one inverter. I was hoping someone knows if it is adjustable inside or fixed. Not...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.Well, Bananaman That thought was good however my last post's uneven voltage readings occurs when all solar feeds are turned off and all...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.OK here are the results of three days of pursuing ohms law! switching battery cables change nothing as regards my push/pull problem. The...
-
JJoel Jahn replied to the thread 6000 xp settings.yes firmware of dongle is v2.06. I see no update for that in the monitor pages.
-
JJoel Jahn replied to the thread 6000 xp settings.my home network password is also numbers and letters. my firmware is ccaa-180COD and it's for the inverter, don't know of any firmware...
-
JJoel Jahn replied to the thread 6000 xp settings.The dongles work on WiFi, they are just a bit stubborn. Did you read my post above? Did you ever get to where the three green lights are...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.Sunshine eggo; looks like your firm belief that Ohms law applies to everything is now making your knees week! That happens when you cut...
-
JJoel Jahn replied to the thread 6000 xp settings.What I did to get the dongles to work (I have two parallel 6000xps). I first added the EG4 app to my phone and registered as the app...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.Ok Sunshine, I see you are excited about Ohms law. So, this what I propose as a test without spending more money. In a couple of days, I...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.There is no queston about it! Further tests are telling me that the battery charger thinks the voltage is higher in No.2 inverter than...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.parallel. battery pos split at battery up to each + and - is the same.
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.I have verified that number two inverter reads (on its screen) the battery voltage at .20v above the battery terminals of itself...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.Sunshine What I cant figure out is why the one inverter thinks it needs to pull a higher than charge value down. You said it! It should...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.Yes Sunshine the pv output are similar but a piece of dirt here and there will change the output. what you don't want to miss here that...
-
JJoel Jahn replied to the thread EG4 6000xp push/pull problem?.yah, well being they are paralleled I would think they should do the same things at the times! They really ack as though they are...
-
-
Loading…
-
Loading…
-
Loading…
-
Loading…
