diy solar

diy solar

Recent content by Leo3

  1. Leo3

    Charge Bluetti AC50S with AC200 brick?

    I have misplaced my AC50S wall charging cord. Can I use the AC200 giant brick wall charger to charge the 50S?
  2. Leo3

    Connecting Bluetti AC200 to 12v DC Fuse Box

    So does anyone have specific instructions on how to connect the AC200 to an RV without just plugging the RV into one of the AC200's AC outlets? I haven't seen specifics on that. Like using the common systems found on a typical RV which is usually WFCO. I've got the aviation plug but I just don't...
  3. Leo3

    Weird issue with Bluetti AC200

    I don’t want to change the thread here but how did you do this?
  4. Leo3

    Bluetti SP120 extension cables

    I bought 100’ of cable and MC4 connector and crimper kit. I try to use affiliate links. I think I got the cable from Will’s page and crimper set from RV with Tito. Then I made two 30’ cables. I still have 40’ of cable left for later.
  5. Leo3

    Cheap 10amp PWM- am I overloading?

    Finally good enough service to post my pic!
  6. Leo3

    Cheap 10amp PWM- am I overloading?

    I just have two panels hooked up in parallel with a branch connector. One is an SP120 and one is a flexible panel that came with my trailer. The sp120 is just sitting on the roof alongside the mounted flexible panel.
  7. Leo3

    Cheap 10amp PWM- am I overloading?

    A pwm is not supposed to lower the amps to 10 right? It should be like an error code instead? I really need to get a 20 amp controller don’t I. Assuming wiring can handle. I will try to get some more data and when I am back in good service I can post.
  8. Leo3

    Cheap 10amp PWM- am I overloading?

    Yes. Positive.
  9. Leo3

    Cheap 10amp PWM- am I overloading?

    Just picture the SCC screen reading 14.6 amps. I can upload pic due to poor service.
  10. Leo3

    Cheap 10amp PWM- am I overloading?

    This SCC was stock in my travel trailer. It’s a 10amp and you can see in this pic it says 14amp. Trailer has one solar panel and I connected another in parallel. Hopefully the pic attached. I’m have bad service. It’s the readout in the SCC showing 14.6 amps input. It got up into the 15’s. So...
  11. Leo3

    Bluetti Wireless Charging

    I seem to have a consistent problem charging AirPod case and iPhone on the wireless charging circles on top of the AC200 and AC50S. I’ve never had wireless charging capability before so I don’t know what to expect, but I do feel it should charge until it’s done but mine seem to just stop after a...
  12. Leo3

    Will's anti-crowdfunding video & Bluetti AC200

    Is the AC200P the newer one that's 2000Wh instead of 1700?
  13. Leo3

    Will's anti-crowdfunding video & Bluetti AC200

    In Will's recent video he mentioned problems with the AC200. What are the problems? I haven't had a chance to really use mine but I'd like to know the issue(s) so I can see if I have them. I am thinking I can do some troubleshooting and see if my unit has the problems. Thanks!
  14. Leo3

    How to get the most out of a cheap PWM SCC

    Good idea I'll do that. Thanks.
  15. Leo3

    How to get the most out of a cheap PWM SCC

    According to the wiring diagram on page 8 of the SCC manual I linked to above, there "should" already be a fuse between the SCC and Batt on the pos wire. However, travel trailer wiring can be hard to follow so I actually don't know. I need a tool to energize the positive wire that exits the SCC...
Back
Top