Recent content by lightmail

  1. L

    Renogy 2000W Inverter Charger Grounding Issues

    I did something really stupid by connecting the neutral and ground together in my 30 amp sub panel supplying my inverter charger (inverter input side). I was in big hurry. I have an error code 02 Xantrex #817-2080. Do you think I permanently damaged my unit. Caught it after one cycle of...
  2. L

    Have I damaged my batteries?

    My inverter slowly comes down in amps and then shuts down. It shows the stages. It doesn't seem to be shutting off immediately. When it reads 12.7 should I just keep running and see if inverter shuts down. It's suppose to do that. I have 2/0 and have a total distance round trip of 11.6 feet...
  3. L

    Have I damaged my batteries?

    My inverter slowly comes down in amps and then shuts down. It shows the stages. It doesn't seem to be shutting off immediately. When it reads 12.7 should I just keep running and see if inverter shuts down. It's suppose to do that. I have 2/0 and have a total distance round trip of 11.6 feet...
  4. L

    Have I damaged my batteries?

    2 100ah Sok 12 volt. when shut off voltage went to 13.2-3
  5. L

    Have I damaged my batteries?

    Help.. My system got up to 14.4 in the sun and then settled around 13.3. I then plugged in a 1200 watt load. Within minutes it showed 12.7 volts. Turned off load. So I turned on shore power and it took the charger about 20 mins to charge to 14.4-14.6. It showed bulk, then absorp then into float...
  6. L

    Renogy Rover 100% reading at 13.3%

    I have validated voltage at battery and controller. How do I know that my batteries are 100%? When do you measure, at rest or under load? They read 13.3 at rest.
  7. L

    Renogy Rover 100% reading at 13.3%

    Hi... This is a van with 400 watts solar and 2 100 ah batteries. I got my charger working and can use that. When it slowly starts shutting down to off, do I assume it's 100%? and then set or do I have to wait awhile?
  8. L

    Renogy Rover 100% reading at 13.3%

    Thank you for response. Yes I am using lithium batteries, and the Renogy has settings for lithium. I have a shunt but can't set it till I have 100% in batteries and I am not sure how to go about that if I can't use the solar chargers 100% reading. I am missing something..
  9. L

    Renogy Rover 100% reading at 13.3%

    I am just setting up my controller. It has run a few days . It says 13.3 volts most of the time. But it says it is at 100%. It's going to be super sunny here in Seattle and I want to get this thing set up right. I have no loads what so ever just the main battery bank, inverter and fuses to...
  10. L

    Renogy Rover Lithium settings

    I wonder why you have Battery Rated AH(AH) between system voltage and battery type. Mine doesn't. hmm. I wonder if it madders?
  11. L

    Renogy Rover Lithium settings

    My BT-1 display is different then yours, every things white, I wonder if they up dated appearance? I just bought mine a month or so ago. Bummer
  12. L

    Fusing problem.

    This will never be hard used watts wise. Maybe 4 or 5 minutes of small microwave. I was going to put 250 amp fuse on each battery to protect my friend from accidentally dropping wrench or something on the battery without a fuse. I see it in diagrams all the time people using 250 amp fuses. But...
  13. L

    Fusing problem.

    Thank you for your reply.
Top