Most reacted posts

I feel dumb now after reading the manual again. It clearly states how to attach the A/C out wires: ground (First) and that wire YES goes to the ground screw on outside of the box. it also says to run the grounding wire to ROD as close as possible to unit. the neutral and Live wires go...

How does anyone actually learn figure out how which setting to program the "i don't know what to call it" the MPPT? the manual calls it all in one solar charger inverter. SRNE HFP3825U80-145. manual...

I'll simplify my question to verify i got this correct. My combiner box has up to 3 spots for breakers. I use Mp4 fuse connectors outside before the box. If I use 2 or three breakers.....my question is......the pos and neg wire LEAVING the combiner box (DCvoltage out) going to the charge...

deleted

My SRNE all in one charge controller I’m too paranoid to connect anything to a/c in. The terminals are stupid small also. I just can’t find enough info to be clear so…. Is it safe to….. My 100Ah lifePo battery has 2 neg and 2 pos terminals. My all in one charge controller attached to one...

I’ll try again and simplify it maybe no replies cause too many words. How do I learn what the settings are supposed to be in my all in one charge controller? SRNE 48v. The manual does not state them. Can’t find any videos or websites yet. Thank you

I apologize for my question offending. I'm glad I asked it, because now I understand max charging amperage. which helps me go forward with setting up multiple batteries.

is the correct place to pose questions about how to program my new SRNE 48v? ******HOW DO I LEARN WHAT EACH SETTING MEANS AND EXACTLY WHAT I AM TO PROGRAM IT TO?******* I have: Battery: Solar Lithium Battery Server Rack - LiFePO4 48V 100Ah (51.2V nominal) 5120Wh Smart BMS Rechargeable Lithium...

i'm truly sorry. let me see if i understand your paragraph. i have a 100 amp hour battery so that means max charging current IS 100amps? but the SRNE setting 07 on page 40...

Thank you for replying very helpful about mc4 and connect in the dark. Love it. . My electrician also said on the phone to connect that screw to ground rods and we spoke of esa inspection before going live. Just so readers know I’m being safe. But doing homework to save time. I don’t...

i think i'm getting this... but...not clear on: setting [04] battery power to utility setpoint [05] utility to battery power setpoint. questions: 1. how to set up a generator safely. any information at all on A/C input for SRNE.

exactly as you described. thank you. yes my breaker panel sub panel....not the main panel...the SRNE must be the main panel so yes as you described...I added a ground bus bar into the subpanel and that is wired through going to the main panel which must be the SRNE all in one....so as you...

how do i check if the battery has a dc or ac breaker? the breaker certainly functions....i switch it off and the battery stops sending power. does that mean its ok? i'm still clueless what how to set the parameters on the SRNE before i connect the panels.....

I personally use a propane instant water heater. super efficient. outdoor non vented cost $200. vented propane instant hot water tank around $500.

Going through EXACT same issue...weeks looking into this, searching everywhere....so far I conclude from what my electrician said, the sales rep, videos watched... 1. have no A/C input otherwise risk of ground looping. 2. the SRNE will be the main panel and the subpanel connected via a/c...

are you still following this thread? i think my previous post means the same thing you said in your last post...not sure.

Will Prowse had same complaint as myself here in this video link at exactly minute five he explains. I bought SRNE inverter, and the AC out has no ground screw. The Solarpowerstore Canada guy said put found on the ground screw located front left lower outside of box. Will Prowse left it...

but that does not answer what combiner box affects coming out of the combiner box. maybe super dumb question, but getting tired... i understand going in...series parallel. so far max voc is 145V and either max 50A or max pv charging current 0-80A. i dont know which one to use... i've got 48V...

hardware: SRNE HFP4835U80-145 where to find numbers to go off of for setting the parameters -01 to 38? Which data sheet can I trust? the battery I bought from solarpowerstore has some specs on the webpage selling the battery. I don't know where they got those or if they refer to every model...

thanks guys. i spent hours yesterday going through manual, trying to learn understand each setting. I'm getting closer. out of the 38 parameters to set...still clueless on a few... i'll post seperate. sooo complicated. max charging current...