Search results

Hi all. I have an Enphase Ensemble system. 3 Encharge 10s on the wall, Empower and Envoy. All the backup loads are on a 200A panel. But...I have 2 200A panels tied to my meter. The OTHER 200A breaker contains the loads that are NOT backed up. Can I use an all-in-one inverter, with a server...

2 brand new Victron Smart MPPT Controllers for sale. $595 (each) plus shipping UPS Ground Never used. Originally part of a project never completed as we sold our fifth wheel.

If texting is easier, I can provide my number.

Struggling with the cost of the Enphase system when compared to what I would get from using 2 Sol Ark 12k inverters with 30kw of batteries from HomeGrid (or other). Any advice? I just don't want to overpay. My roofline is almost always in the sun, so do I really need microinverters? Thx.

I am new to the group but not new to Wills videos. I am struggling to make a decision about what type of battery backup system to use. Cost is a large factor. EG4 server units are clearly the cheapest. But I'm not sure how they compare against, e.g., Fortress eFlex. The Fortress batteries are...

Brand new, never used. Will ship in original packed box. $2000 OBO Local delivery in Charlotte, NC Otherwise, shipping cost can be added and would be based on weight and location.

UPDATE: Cerbo Gx and Smart Shunt sold. Remaining components Hi all. I started a project but never finished. All equipment is brand new and available as a set or by component. If local to NC, pickup is recommended due to weight. 1. Quattro 24/5000/120 - $2700 2. 2 Smart MPPT Solar Charge...

No. They are DOA

Thx!

Correction. I'm probably just using wrong terminology. My 50A shore power wire has 2 hot legs and a neutral. Pretty sure it has a ground as well. I'm using a manual transfer switch with a jumper wire so that I can switch between shore and battery without losing total power on both legs of the...

I am using a run of 6/3 but I am running one hot leg through a transfer switch that is too far away for the existing run.

If anyone has one for sale, please message me. Thx.

This is a 6/4 50A plug and I need to extend 1 of the hot legs

Hey all. In my 6/4 flex romex run from my RV's 50A plug to my Victron Quattro, I need extra length for one of the 2 120v hot legs. I assume it is fine to connect 2 runs of 6AWG with a positive bus bar. But I also assume the connection should be fused. 100A ANL fuse ok?

Hi, If anyone has 8 gently used 280ah EVE cells, I may be interested. I could pick up so no shipping needed. Thx.

Thx for the helpful info. None of the valves are popped. Just swollen pretty good and I see no evidence of leaking. I'll give it a shot. Wish me luck!

I stupidly got a power supply that wouldn't let me set voltage appropriately in an effort to charge with higher current. Live and learn

Folks. Don't leave your charger unattended. Left mine on overnight and woke to find my 1s8p cells I was trying to top balance at 4.7v. They are way swollen and I'm considering them DOA. Lesson learned.

The xCharger uses 12AWG wire for its connections. So I wasn't sure how to connect a larger size wire to the plug that goes into the x8 output. So I just used the same size. Thoughts?

I took everything down and am now charging direct from the power supply. Voltage on the PS won't go above 3.5. Current is at 31A. The batteries are now at 3.32-3.33. I left them off overnight and have just started charging again this morning. I'll write you know what SOC is at the end of the day.

I'm very new at this so I'll give a shot at answering the questions. The wire I'm using is 12 AWG because that is the size of the output wire from the connector to the iCharger x8. It is long, so I can reduce the size and see if that helps. All nuts are tightened appropriately. Wires with clips...

I am charging 8 280ah LiFePo4 cells in parallel using a TekPower TP1560E power supply and an iCharger x8. I have all parameters set and the iCharger Life profile at 3.6v and 30A. All cells are hovering around 3.3 and have been for what seems like forever. Even though the iCharger is set to...

Hi all. I'm working on my new system and am wondering about some things that are likely old hat to the veterans in the group. I have a Quattro 24/5000/120, coupled with a 24v 8s2p 560ah battery bank and a Victron Smart Shunt. I have 2400w of solar on the roof in 2 arrays (both arrays of 6 are...

Hi all. I'm trying to decide between a single Victron 24/5000/120 Quattro and 2 MultiPlus 24/3000 units in parallel. I have a 50A RV in the typical setup where 1 hot powers half the circuits and the second hot powers the other half. I understand I can use a MTS and a jumper to ensure my entire...

$2600. New in the box. Never used. I've just decided to go with 2 Multiplus inverters in parallel instead. These sell for $2,900 + tax (~$200) + $250 for shipping. Will sell for $2,600 OBO and would be willing to meet in NC, SC or VA to save shipping. Otherwise, will ship at cost. Thx. John

Is the MP workable as 24v?

Hi all. I am seeking a resource to determine the proper settings for my Victron smart 250/60 SCC. I have 2 8s 280ah battery banks connected in parallel, so 24v 560ah total. I purchased them from a third party so I don't know how to yell who made them. Thinking CATL but not sure. Attached are...

Hi everyone. Any pointers when installing a 3 way manual transfer switch as part of my solar setup for our 50A RV what guage wire I should be using on the switch. 10AWG works well but 6AWG does not. Thoughts? Thx!!

Good idea. I may post there too. Thx.

I have 8 for sale. See my post from tonight, with photo.

I'm in Charlotte. I have 8 280ah cells for sale for $1000. DM me if interested. Just posted in this forum.

I have 8 brand new 280ah cells for sale for $1000. I top balanced them and had planned on using but now have a family member in need. I'll sell 4 for $500 as well. I'd sell this complete battery pack of 8, with Overkill Solar 8s BMS, for $1250. I'm in NC so if anyone is interested, DM me. Thx.

I have 8 280ah cells but could sell you 4. Brand new. Only top balanced. Where are you located?

Sold. Thx.

Thx