diy solar

diy solar

Search results

  1. R

    Missoury wind and solar

    I got a free missoury wind and solar wind turbine, Its 48v 1500 watt Down side is : i dont have a rectifier and no charge controller Will any simple/ cheap chinese controller work on this turbine ?? I dont want to spend a lot of cash on this project Btw : my solar system is also 48v Your...
  2. R

    2 mppsolar inverters 1 battery bank

    Opinion 2 mppsolar inverters Each has its own solar array Connected via victron smart shunt , charging the same battery bank All settings are the same , bulk, float Low bat voltage etc etc etc will this work??
  3. R

    2 mppsolar inverters 1 batt bank

    Hi guys Your opinion on this setup 1 nissan leaf battery bank 8p7s 2 mppsolar inverters pip 5048gk each has its own solar array 1 victron smart shunt Bulk 57.5v Float 57v I want the 2 separate mppsolars charge the same battery bank via 1 victron smartshunt All voltage settings will be the same...
  4. R

    Sun elec miami fl

    Hi guys im gonna buy some used solar panels at sunelectronics international in miami florida 15901 nw 59th ave in miami lakes 33014 so i wanted to know if you guys know the place , have bought panels there , good quality used panels etc etc Ive been recommended to them via this page , but i...
  5. R

    Sunelectronics international miami florida

    Hi guys im gonna buy some used solar panels at sunelectronics international in miami florida 15901 nw 59th ave in miami lakes 33014 so i wanted to know if you guys know the place , have bought panels there , good quality used panels etc etc Ive been recommended to them via this page , but i...
  6. R

    Something wrong ?

    Pip 5048gk mppsolar inverter 2 x 10 panels in series than paralel to the inverter panels are 250w 8.5 amps Open circuit they all measure around 33v if i measure 1 string (10 panels in series) on the roof i get around 320v, which is good The i go measure at the breaker before going to the...
  7. R

    Pip 5048 mpp solar

    Hi guys what are the best battery settings for my 48v solar system Meaning bulk , absorption and float voltages thnx
  8. R

    Victron compatibility

    Is the victron 150/100 charge controller compatible with other brands charge controllers? i want my victron 150/100 and a Mppt solar charge controller charge the same battery bank but each ch controller has its own solar panel aray possible ?? pics for reference
  9. R

    2 victron charge controllers

    Question/ opinion can i use 2 victron charge controllers to charge the same battery banks One is 150/100 and the other is 100/50 Thnx
  10. R

    Victron bvm712

    Hi guys how do i wire / setup my victron bvm 712 smart battery monitor to turn off my inverter at a certain preset low voltage ??? Any one of you did it ??? My inverter has the remote on/ off switch also
  11. R

    Automatic transfer switch

    Hi guys im looking for a dual power automatic transfer switch so i can switch over when my solar system gets low on battery power , gives then a signal to the ATS switches over to grid power , while batteries charge 220v and amps should be around 125/150
  12. R

    Victron 150/100

    In the victron 150/100 charge controller manual states to use 35 mm2 wire / 2 awg to connect to the battery pos and neg busbar Opinion about using 25mm2 wire/ 4 awg which is also capable of supporting the max of 100amps which the charge controller can send to the batteries and is easier to get...
  13. R

    Ah setup aili batt monitor

    Hi guys, Just to confirm if i did set up my ah right in the Aili battery monitor my solar system is 24v I have 24 , 190 ah batteries 12 pairs to make the 24v so i setup the ah as following 12x 190ah = 2280ah Ofcourse only 50% usable , that makes it 1140ah so as i reach 0%on the...
  14. R

    Aili bat monitor

    I installed my aili bat monitor in between the neg bus bar ( all - batteries ) and my 6000watt inverter ( neg side input) the monitor works great Shows voltage I adjusted the batt ah in the settings Shows amp draw Full battery is allready programmed to 100% Now my problem After using (...
Back
Top