diy solar

diy solar

Search results

  1. B

    battery voltage discharge rate

    I have 3 lipo 12v batteries...wired in parallel. They are 208 ah each. Giving me 618ah at 12v. I believe this is correct. When I hook a load to them. What will the voltage do with the 3 batteries in parallel. Will it drop drop the same as one battery at 12v. Drop slower or drop the same speed.
  2. B

    Epevers 100amp SSC

    I have an Epevers 100amp SSC could someone tell me what the Load part of the SSC does. Does it need to be set or something wired to it
  3. B

    AC vs DC appliances

    Need some advice...I just build a small camper out of a 6 by 12 cargo trailer for dispersed camping. I am putting in 3 12v 206ah lithium batteries in parallel. So 12v 618 ah. 800 watts of solar. 100amp mppt solar controller. A aims 3000 watt to 9000 watt surge inverter/charger. My question...
  4. B

    Renogy dc to dc charger

    Looking to get a 20amp charger. I see the charger does not come with the two small connector plugs and wires. To connect to the ignition. Think called D + . I can't seem to find them or the plugs. Does anyone know where to get these plugs. Would also like to know if anyone has installed one of...
  5. B

    Need a little info about a solar controller

    I have a 40 amp Epevers solar controller. I am just wonder about the wiring hook ups. Two wires come from the solar panels. Two wires go to to the batteries...and the last two say load. What is it that you do with the load terminals. I am putting in a 12v fuse panel. Is the load on the solar...
  6. B

    rv converters

    I am installing an Aims 3000 watt inverter/charger in my Rv. Someone said when you put it in...to disconnect and remove the small converter from you Rv. Well I looked at mine which is mounted under my panel box. Seemed simple enough....has 3 wires hot, neutral and ground...and 2 wires to DC side...
  7. B

    Ali battery monitor

    I have a ali battery monitor...set up and working great. However...I updated my lead acid batteries... to 2 lithium batteries...206 ah each wired in parallel. This gives me 412 ah...if I'm correct. I tried to reset the ali monitor to 412 ah but....it keeps showing the original 212 ah that i had...
  8. B

    100 amp epevers solar controller

    Controller is driving me nuts. It says to connect remote battery voltage sensor ....I see where to hook it inside the controller...but there is no controller....???? Says to connect a cable from the battery to the connection inside the controller. So is this just a tiny wire you run from the...
  9. B

    aims inverter/charger

    I'm installing an Aims inverter/charger. It came with a LCD wall monitor. Diagrams show both a shunt installed on the negative cable battery cable (not a smart shunt). And a breaker/fuse on the positive leg. So I'm not sure why a shunt on the negative cable if its not a smart shunt to be plugged...
  10. B

    Shunts

    I have an Aims 12v 3000 watt pure sign wave inverter/charger installation diagram shows a DC shunt between the inverter and the battery on the neg. cable. It does not show the amperage of the shunt. Anyone know what it should be rated at ??? It also shows breaker or fuse inline on the positive...
  11. B

    shunts and monitors

    How do you figure out what size shunt to use for a battery monitor. I bought an AiLi monitor and it came with a 500amp shunt. Seems to work ok. Now I have bought a Epevers 12v 40amp SCC...I don't see a shunt with the separate MC50 monitor I bought for it. I am also installing an Aims pure sign...
  12. B

    Charging LifePO4 batteries

    I just ordered 2 SOK LifePO4 batteries.. I need a MPPT Charger for them. I saw Will on a you tube video with a EPEVER MPPT Solar Charge Controller 40A 150V charger I was looking on Amazon about buying however....it lists all the batteries it will charge but it doesn't list lithium. It does say...
Back
Top