Search results

Very nice!.. Congrats!

For those interested, here the release notes for the latest Enphase IQ Gateway Firmware (7.3.517):

Good observation! I better understand your issue now.

FWIW, I am not the original installer of my system. I wasn’t even an installer!. But after becoming certified through their online university program, I gain full access to all equipment. I can get replacement parts sent to me directly instead of those being sent to the CO that installed my...

I have seen this same behavior with my system as well. Does not happen often but when it does, there nothing in event logs to indicate there is an issue. The high-RES data shows everything normal. no current drops, no frequency shifts, nothing. On the next reporting cycle, the values return to...

Signal strengths to batteries improved and remains strong. No more Zigbee comms failures! As for the system, I wish I would have purchased more panels but at the time that was not possible. During this past summer, the production was a bit lower than consumption due to the AC being on all the...

For those interested, here the release notes for the latest Enphase IQ Gateway Firmware: Firmware Version 7.3.120

Heads up.. ver D7.3.76.220818 (8888e6) for the Gateway was released a little over a month ago. Also, ver 1.5.4604_rel/21.23 for the System Controller.

Have you submitted a system design for review? This was required at least when I went through the process.

With the recent heat wave here in the south, my panel temps have been over 145°F!. Production has taken a hit for sure.

Enlighten Manager Upgrade Program I got access after I completed their installer certification program.

I get to it from enlighten manager.

That's the new V2 dashboard. Big improvement over V1.

You are not alone.. My "Fuel Cost" went up starting this month as well.. Fuel cost used to be around $12-$15. This month it was $40!!. My energy Cost was just $23.

The grid profile is changed in the envoy(Gateway) then it propagates to: inverters, controller, batteries. With all the new access restrictions Enphase has added lately ,I don't think( will need to check) if that option is available without using ITK(Installer Toolkit).

Congrats!!.. I too got certified a few months back. They reviewed and approved my design within two days so you should be hearing from then soon.

Very Nice!!.. Congrats!

Nice Job!... Do you clean the panels on the regular?

Old thread but interested to know if and when 5G will be implemented. I know currently Enphase has 4GLTE cell comms kits from both ATT and T-Mobile.

Had my highest daily output so far a few days ago…. I want to add another battery but think I will wait out till the year is up.

Took a page out @svetz playbook and moved the zigbee dongle out of the Combiner box and closer to the batteries in an attempt to increase the signal strength between the batteries and the envoy in the Combiner Box. Here is where a I mounted the weatherproof box with zigbee inside. Here is...

So I opened up my comms kit enclosure to extend the radios outside like you did and look what I found… I called Tech support to see why my comms kit only has one radio and not the two listed in the documention and I was told by two different techs(I called a second time because wanted a second...

Well, I got that from the install guide. I guess that sub GHz radio is some sort back up comms... Its listed as 915MHz on the pic

NM!…Apparently there are two units inside…,.

like your idea of moving the Zigbees. But did yours come like, two separate dongles? This is what I have.... I wonder if there are separate units inside. There are two cables coming out with one USB plug at the end.

Also, v21.23 is rolling out to all devices. Envoy v07.03.63

This will be implemented on future hardware release. Unfortunately for us, this will not be backwards compatible. :cautious:

Nice work!!.. Does the signal strength fluctuate throughout he day?

Lol!.. the names did changed. He just had them mistyped!

Thank you for sharing. I’ll be on the lookout for this update.

No worries!, I have a ticket open for that issue. ITK is supposed “automatically” select the correct software to update to. And in my case, it’s prompting me to update to the wrong version.

I’m on 7.0.68 when I connect to Envoy, ITK prompts me to update to 7.0.69 but according to settings page, 7.0.69 is for systems with M series micro inverters.

Isn't software 7.x already out? unless they are referring to a global roll out.

Testing as well as provisioning can only be done with the Enphase ITK. As others have mentioned, you might be able to use other methods but you risk "breaking" something.