Search results

I have 2 EG4 6500w inverters running 120v to each leg of my breaker panel. inverters are set to 120phase and have them reading as 2p1 and 2p2 with battery as main power source. each line goes to a 60Amp double pole breaker. all wiring is to code. this system is powered by (5) 48v 100ah lifepo4...

I have a 24v 6000w pure sine low frequency split phase inverter. I have a 3hp air compressor pump that blows air down my well casing running on a 3/4 hp motor with my wheels being sized properly to support a low air pressure driving from the belt. this fills my water storage tank. I have a 1/2...

I have (2) eg46500ex paralleled together. I have them set on 2p1 and 2p2 and both are set to (user) for an open loop system. I have (4) lifepower4 batteries. The issue I'm having is that both inverters will charge my batteries andthe inverters are showing full amperage and voltage coming in...

I have 4 pv arrays 8s 7s going into 2 going into each of my eg4 6500EX inverter.i have 30 panels that are 37v 230w. master inverter reads (8 243 v 56w (7s) 230v 77w. 2nd inverter reads (8s) 200v 36w (7s) 220v 45w. numbers stay close in voltage but watts seem to change sometimes up to 350...

I'm running my 2 eg4 6500EX parallel and completely off grid. Are the current sharing cables necessary

I have (2) EG4 6500w inverters set up for 240 split phase. I have (3) EG4 Lifepower4 batteries. I understand how to connect the batteries with the rs485 cable and to make sure that each battery had a different dip setting and that the host battery needs to be 0. I've noticed on online videos...

I know this isn't code and the dangers of blowing circuits and possible death. I'm asking this just for personal understanding. If you ran your entire split phase system into electric Company service pole and shut off the main 200amp service breaker it would not back feed the utility power. Vice...

I have (30) 230 watt 37v 8 amp monoTrina solar panels. I have (2) Eg4 6500EX 48 inverters that will be setup up for split phase output. My question is are both array inputs on the inverter allowed to handle the 500v 4000w input. I believe that is correct from reading the manual. If so, I can on...

I have a pv array of (20) Trina Solar mono 230w panels that are 37V and 8.26A. They will be 10S2P. going into a pv disconnect. I have (2) EG4 6500w inverters that will be paired for 240v split phase. Does it matter which inverter that the array goes into? Or should I run 10 in series to one...

I have 3 of the basic model eg4 48v 100ah batteries. I'm not using a server rack and was going to connect each battery in parallel with 4/0 wire. I was then going to run power from top battery and negative from bottom battery also using 4/0 to my busbar and fuses. Is this overkill for wire or as...

I have a eg4 6k split phase all in one inverter and (2) eg4 48v 100ah batteries. I will going off grid totally connecting into the existing service panel with a 200amp breaker and removing the meter. I will be using a class t 225 amp fuse between battery and inverter. I was going to use 4/0 to...

I have a split phase 24v 6000w sungold power inverter. (6) HQST 200w mono solar panels (3)s (2)p. I checked the panels and there output is fine on each panel. I have (4) weize 12v 200ah lifepo4 all new and were fully charged before installed. The batteries are made into a 24v 400ah system. You...

I'm looking into setting up a solar water heating system that is completely off grid. I'm single and live in small manufactured home. I mostly work and gone during the day so I use little water. I live in southwest Louisiana which rarely goes below freezing. I currently have an electric 4500...

I'm returning an 60 amp Epever Tracer mppt charge controller. It's parameters were falsely advertised. I'm seeking a recommendation for a trustworthy 60 amp mppt charge controller for a 24v system with a LiFePO4 setting already in the parameters. It will be receiving power from (6) 200w mono...

I bought this Epever 60amp MPPT charge controller. The seller I bought it from lists it as 24v and LiFePO4 compatible. Upon receiving the product, there is no set parameters for this unit for my application. I have the MT50 and was able to put it into a user setting. In that setting I put my...

I have a sungoldpower 6000w split phase LF Inverter. I have (6) 200w mono panels 3s2p. I have (2) 12v 200ah weize lithium ion phosphate in series. I have a 60amp Epever mppt charge controller. The inverter runs everything fine. Nothing tripping. My controller shows full charge batteries, my...

I have (7) 200w mono panels. 9 amp working current. 4s and 3s then 2p. My system is 24v 200ah.soon to be upgraded to 400ah. I have a 60amp mppt Epever Tracer charge controller. Mathematically it should handle 1400w. My panels out me around 1440 am I too close to the border and should I upgrade...

I have (6) 200W 22v 10amp panels, 24v 400AH lithium iron phosphate bank, sungoldpower 24v 6000w low frequency inverter split phase 240 output, 60Amp Epever Tracer mppt 150v max input and 1500w max on a 24v system. I will be running a 3/4 hp motor to fill a 275 gallon water tank and a 1/2 motor...

I have (2) 24v 3500 watt reliable pure sine wave inverters. I am using them for my off grid well system. This system will have a 3/4 hp motor turning an air compressor to pump air down well casing to fill a 275 gallon storage tank. Then I will be using a 1/2 hp shallow well pump with a 20...

I have a Renogy Rover Elite 20Amp charge controller with (2) 100W HQST Mono panels that are wired in series. My battery is a ecoworthy 12v 100AH and I have a vevor 2000W pure sine wave inverter and a blue sea fuse block. I Everything is new and just been installed. I'm getting a voltage reading...

This is for me a single man living in a single wide trailer located in DeRidder, LA. I'm working most of the time and already have a solar pond irrigation system for my garden. So I don't have huge water needs. This will be a completely off grid system. I will be filling a 300 gallon tank using...