diy solar

diy solar

Most reacted posts

  • Post in thread: Building my first LiFePO4 battery bank for a caravan

    Hi to all the DIY solar enthusiasts I was originally planning on building 12v 200ah bank using 2 12v 100ah batteries in parallel. They would be used in my caravan to travel off the grid around Australia. After reading through this very informative forum, i noticed the great deals with Xuba...
  • Post in thread: BMS common port vs seperate port

    I was told by Redarc manufacturer that they tell their clients to jumper a external 12v source to the battery terminal to restart their solar controller. Their new combination dc to dc / mppt controller will repower it self from a solar or vehicle 12v power source without 12v from battery. I...
  • Post in thread: Building my first LiFePO4 battery bank for a caravan

    Hi Chris I will check out RJ energy. How much was the freight and what form of transport did you use. Seem like a lot of people like the suppler called Xuba on Alibaba. Did someone recommend RJ energy. RU building 2 *12v batteries or 24v. What BMS will you be using. Thanks Emmanuel
  • Post in thread: Xuba Electronics: DEAL - 280AH LiFePo4 cells. Purchase & Review

    Working in metric units. Building a compression frame with 2 end plates and 4 threaded rods with nuts, one in each corner. It would be handy if someone could calculate the torque in newton/meters that would have to be applied on each nut to create a force of 2942 newtons on the cells. The...
  • Post in thread: Xuba Electronics: DEAL - 280AH LiFePo4 cells. Purchase & Review

    Cinergi Thanks for pointing out the post. Luthj suggest 12psi or 82Kpa pressure From this online torque calculator https://www.engineeringtoolbox.com/bolt-torque-load-calculator-d_2065.html using rod dia .008m, force 2942newton, k=2. Torque nuts result around 3Nm. Doesn't sound very tight.
  • Post in thread: Building my first LiFePO4 battery bank for a caravan

    Did RJ energy charge you GST or do you have to pay it at some stage through customs like people in the US and Canada have to. The packing looks really good from RJ energy compared to XUBA packaging. Considering one of the main complaints about Chinese supplied cells are damage in transit. I will...
  • Post in thread: My 12v 280ah build thread

    Hi Josh I'm planning on building a similar battery for my 16 ft caravan. Was going for a smaller 2 bank of 12V 100ah but saw the good price of theses 280ah cells from XUBA. It's just the price of freight that is expensive. Will be watching how you build goes.
  • Post in thread: Charging parallel connected battery modules with sperate BMS

    Only if you have a tendency to drive on the wrong side of the road.
  • Post in thread: My 12v 280ah build thread

    Was that under $500 including freight. XUBA have the 280AH listed for $476 for 4 cells plus freight $363.
  • Post in thread: Australian Battery Shop

    These cells on Facebook look very much like EVE cells that Amy sells on Alibaba but not sure about the price difference.
  • Post in thread: EVE 280ah 24v battery frame

    Thinking of using plastic A4 book binder sheets. They are around 1mm thick. As long as the supplied cell buss-bar's are long enough to link terminals.
  • Post in thread: Internal Resistance Meters. Any recomendations?

    Just wanted to know the difference between a/c Z and DC IR because if i purchased some cells from Alibaba, i would only be able to test DC IR and compare it to the a/c Z value in the manufacturers spec sheet EG EVE 290ah 0.25 m ohm a/c. To determine if the cells are new and A grade or used...
  • Post in thread: DGJBD Bluetooth BMS - a short review

    Hi Thedodgeronlin Yes Agnes water is still a peaceful beach side township It's grown a bit since i used to come here for school holidays. Been retired here for a few years. Will do Can you private message on this forum
  • Post in thread: Internal Resistance Meters. Any recomendations?

    I intended to use the internal cell voltage drop( no load - load voltage) to find the cell IR= V drop with load/ current in load. And with the higher test current you may get a more accurate figure because the cell voltage drop to load current may not be linear at lower currents. Is this cell...
  • Post in thread: Charging parallel connected battery modules with sperate BMS

    Hi I was considering building 2*12v 120ah batteries in parallel with separate BMS's but are concern that if the situation like you explained occurred where one weak cell in one battery caused a LV disconnect and the other good battery and charger would still charge the disconnected battery...
  • Post in thread: DGJBD Bluetooth BMS - a short review

    Hi Pierre Thanks for your review. Been down your way in 1995 when south Africa won the world cup. Was in Joberg for the celebrations. Spent 3mth travelling all round south Africa and Zimbabwe. Walked up table mountain twice. Cape town was my favorite spot. Less violence. friendly people those...
  • Post in thread: DGJBD Bluetooth BMS - a short review

    Hows it Pierre My parents are Dutch and have a uncle that lived in Durban. I don't think he had trouble picking up the Africans language. Like you i like the idea of using a laptop to communicate with BMS I found a youtube video that you may have not seen that mentions a guy that has played...
  • Post in thread: EVE 280ah 24v battery frame

    The plastic sheets would be extra protection between the cells when compressed. Going what i have read on this thread. EVE cells only have a thin insulating film on the aluminium casing to isolate the positive of the cell .
  • Post in thread: Charging parallel connected battery modules with sperate BMS

    Yes i was intending operating 2 batteries in parallel If one battery had a faulty cell (eg high Z or out of balance) causing the BMS to prematurely disconnect due to cell over voltage during charging or low cell voltage during discharge. the good battery would supply the load. My concern was if...
  • Post in thread: Australian Battery Shop

    That's maybe why the facebook 280ah cell are nearly double the price. Even when your paying upfront for the cells when ordered

diy solar

diy solar
Back
Top