Most reacted posts

Hello, Gobel says: Hello Christophe, Have a nice day! I understand your concern. Regarding the labeling of the cell as GP-Cell-280Ah, this is done by the factory to group batteries of similar capacity into the same model for export customs declaration. The actual model number is subject to...

yes but at 522€ you waited 2 months for delivery?

Good product 568€

Hello, here are the settings with a single battery, it works very well and the soc is correctly reset to 100%. What would be your setting recommendation for a second battery as a slave?

I want to buy the EVE 306 Ah MB30 cells, is there a real advantage to compare the LF280k cell

Thanks

Sorry 80 usd with the fees in effect but the site looks weird, wis-tek.com right ?

Apart from this big variation in value, I am completely satisfied with the operation of my battery, and the balancing is done very very well at the end of charging and the soc goes to 100%

the 4 cells are next to each other so I can discharge all 4 together, all that remains is to find the right resistance

I FIND WISTEK VERY CHEAP 79 USD EVE MB31

That's it I received my cells and I have to make my first charge I have questions however because I misunderstood how to make a charge on the voltage with my victron for: do your initial charge based of voltage, choose a charging voltage of 56v, I set dvcc to 56v, right

Bonjour, je ne comprends pas pourquoi je n’ai pas le statut de charge ( bio, absorption). Pourtant j’ai bien la version 4.3 sur iOS ou Android avec le Firmware 4.38

the wistek site is working very badly, what did you do?

Hello, what are the right settings on the Bms side and also on the victron side for a 51.2v eve 280Ah battery in Ess mode, indeed I saw that sometimes the value of the soc is incorrect

Good morning, I would like to order EVE MB31 cells from wistek for €80, has anyone tried? Are you satisfied?

I still have 2 cells in the lag is what I can use a 3.65v regular laboratory power supply in parallel of each cell to raise the voltage, without disconnecting the cells in series in the bank.

I hesitate to put mg 847 or cw7100 paste, do you need a large quantity?

Do you have a link for the download for the Victron special?

https://wis-tek.com/

80 AVEC LES FRAIS EN VIGUEUR MAIS LE SITE A L'AIR BIZARRE WIS-TEK.COM

For my part, I did not shorten the wires that go to each cell because they are PCBs.

Hello, I just finished my seplos v2 battery and the cells are balanced, I have a Victron Multiplus with CAN communication connected to the battery, the battery soc goes well to 100% with the BMS settings. I wonder about the calibration of the BMS, is it good if I charge at 100% and unload until...

Hallo, ich habe eine Frage, dieser Schritt muss nicht gleichzeitig mit Schritt 4 durchgeführt werden, damit der Soc zu 100% initialisiert wird: 7Ändern total-pack-overtension-protect auf 56,8

it works for me, I feel like it's important to calibrate the voltage properly, I increased it by 10mv to properly engage the rcv timer. I still have trouble calibrating the current properly though, still a little drift of the soc.

No

Hello, is it not a type A CAN cable that is needed between victron and jk ms?

Good morning, Does anyone have the right settings to make the mason kit work with a bms 2.0 or the 10E with a victron multiplus 2? I would need the parameters to modify on the bms side but also on the victron side. THANKS

Good morning What would be your optimal settings? I tried that but I'm not sure: I have two 330Ah banks LIFEPO4 JKBMS SERIE JK-PB Battery capacity 660 Ah Charged voltage 55v (tension absorption 55.2v) discharge floor 0% tail current 3% charged detection time 5m peukert exponent 1.01 charge...

5% DE RÉDUCTION Code: UIKFGRD5

Hello, when I see some screenshots of your BMS, I find that the values of the cell resistances are high for me. However, I put silver conductive grease, such as chemtronics cw7100. Do you have an explanation?

I will install my grade A + cells in a Seplos Bms 2.0 box is that if I invest in a Neey 4A active balance box I can do without a top balance it will prevent me from buying a laboratory power supply

Hello, I don't understand, I haven't been able to balance the cells for over a week. I used Andy's settings, when we reach the end of the charge the voltage of 4 cells quickly flies to 3.65v and the others stagnate at 3.35v, what to do?

I endured saying that there was a Firmware 15.29 that solves more problems, do you know where we can download it?

Merci, Que puis-je utiliser comme résistance ? 300w 12v ?

Thanks, What can I use as a resistor? 300w 12v?

That's it I received my cells and I have to make my first charge I have questions however because I misunderstood how to make a charge on the voltage with my victron for: do your initial charge based of voltage, choose a charging voltage of 56v, I set dvcc to 56v, right?

What is the current version of the Firmware for the bms 2. 0 10E

Thanks a lot. In fact I haven't ordered the neey yet, if I understand correctly it's essential…

What cell do you recommend for domestic storage? Hithium HSEV grade A 280 Ah or 314 Ah ESS

Il y a aussi GOBELPOWER avant un code de réduction de 5% jusqu'à la fin du mois