Most reacted posts

Fixed two wires in wrong place JBD need to fix the wiring diagrams for uk and US market hard to read two wires in wrong place JBD smart bms sensing 16s battery config i.e. 48v not 8s 24v :) frog star drift app work with this BMS

Have solved my remote comm to JBD-AP21S001 bms with RS485 port not fitted on pcb but with blue tooth dongle with JBD UART to usb adaptor remover blue tooth plug and replace it with UART adaptor plug you can now read bms information remote to VRM Portal :) now looking Y cable so that both...

you can see remote comm is posable with out Rs485 and only blue tooth or uart adapter made by jbd from amazon. driver work as installed

Right fogstar energy ESR51.2V rack battery comm with Victron OS using VE Can Victron VE. can to battery BMS can bus type b cable required Use the supplied RS232 to USB communication cable and the PbmsTools software to check and setup the BMS can inverter protocols (password needed )...

up date new pack arrived as going to add one more pack to make upto15 kwh with new pack installed and addressing set up. Shown up Victron vrm and new pack at top and mid pack charge up uk, but lower pack site 80% 54.432 v all time and will not get 100% >56 v and < 2amp ( only drawing 0.07 amp...

you have update model new model

you have new model 200Amp JBD bms with blue tooth or remote Uart comm old model has 6 connectors

Victrom m plus 2 you think have problem using two Fogstar 5.12kWh server rack batteries Battery 1 lions share of charge current 33 A 81% soc and battery 2 1.6 amp 67 % on PbmsTool batteries are in parallel with pos/neg supply cables to opposite ends Battery 1 lions share supply...

uart comm only with this spec if you look at the app from JBD one setup is drive so made to protect battery pack in a elect motor bike

FOGSTAR UK CUSTERMER SERVERS back on form :)

rasp Pi4 rasp Pi4 with venus so 2.91 showing remote console devices list Communication Box -JBD UART Communication Box Intelligent Lithium Battery Protection Board USB 2.0 Interface Brand: OKBY this also communicating with Victron inverter

fogstar ESR51.2v pace bms on Victron Os with Can bus yes you can this providing Victron QA department do not miss any more wrongly made ve can to bms can cable that's three going back see below

Up date pack with the charge and discharge problem was shipped back to fogstar and now been overhauled software update and wiring so one battery had not been charging and discharging and had been over loading the other battery pack but thanks to the hard work from Ben from fogstar sorted it...

Still awaiting order completion frogstar server rack battery's - battery look good build but as to how bms work each outer and the Victron system will have to be a later up date as all cables are missing from the order made back April 2023 and cap it all mist the G99 test date with dno so...

JK-B2A820P bms has to have Rs485 interface witch one ? any one have then available out side chine

JBD Ap21S001 200A 6s to 21s bms for sale uk blue tooth and uart comm £135 can post at cost

JBD Ap21S001 200A 6s to 21s smart bms for sale uk blue tooth and uart comm can post at cost £134 working only needed sale up grade

JBD-AP21S001 remote coms it has BT that works fine. RS485 socket is not on the PCB ? also has GPS socket is on the pcb just trying to find out if you can add JT socket will the RS485 work ?

two type rs485 made by JK and only one will work with JK-B2AS20P 4S to 8S BMS and two other types jk bms and the other one work with bms that start 8s up to 20S from ebay and jk bms New message from: googolbuy (26,013) Hello, Our 485 converter is suitable for your BMS. Pls see the...

thanks

no and keeps tripping mcb and ben from fogstar looking get the pack ship back and check out pack wiring will report back next week, solar kwh short to much liquid sunshine

jbd bms lifepo4 (with Bluetooth) - 16s 48v 200a) i have my 24v battery pack built and bms instilled with cell wiring mod main is that xiaoxiang app will not let me change battery pack voltage low and high set points on the bms you can change them but it retunes to default i.e. 48v 16s...