Most reacted posts

Ok, get it done by myself, opened the sd-card in an other linux system: First removed the password check in /etc/passwd from root:x:0:0:root:/root:/bin/bash to root::0:0:root:/root:/bin/bash then in /etc/ssh/sshd_config (only the changed lines) Port 22 PermitRootLogin yes...

All the Daly Accessories you can buy here: https://www.aliexpress.com/item/1005005234080787.html The software for PC, to connect to the RS485 Port, you can download here under Resources. You can add the active Balancer in parallel, they just work independent.

Looks great! But you are not using Victron Inverter, right? You are using RS485 to communicate with the Inverter... Was it necessary to program the interface boards (WNT)?

Ok, for some reason you have to also modify /etc/shadow, even you don't need to enter any password: root:$y$j9T$ENxjb9crH9Rf43ZvEU5K//$gUc0L1WSGNRiLA5a1w5vxKONSaa2LrxThvcoyShmVh8:1 so root password will be: 1234

I would also like to change some Grafana Stuff, like Captions and so on, I managed to get to get to the user login: http://orangepi3-lts/grafana/d/sa-charts/charts?orgId=1&refresh=1m (removed &kiosk=tv) Then you have on the left side the login ability, but I didn't find any user to log in...

Which images? :unsure:

Thanks, that was my next thing to try, I read your attachments... (y) Do I need the terminators? On the Victron? On the Interface Board?

I searched all the program on the PC, but I didn't find such setting, where is it?

They Updated the App, I had the same problem, it should work now... I'm trying to connect to an Victron Multiplus via CAN with that Interface Board, did someone managed that? I'm not sure, but I think with usual cable it is not possible, right? I need to rewire that?

As far as my experience is, you first have to assemble all 3 battery packs, each with its own BMS and interface board. Then you need to set the ID of the interface boards to #0 (all DIP's down) and connect it to PC with an USB-RS485 (RJ45 jacket) Cable. Then take this BMS Monitor Software to...

Found it, was a little bit hidden ? What exactly does 0.2 mean?

Hello, an Friend of mine, also with an Daly BMS and WNT Board, has that problem, where Victron is Dischare when it is Charging and vice versa: In the BMS itself this is showing correctly. Is there any solution for this? Greetings Jack

Hello again, now my system is running for a while, seems ok, except of absence of the sun... :( I have only one thing left, where I'm not sure if this is ok or not: I have two Energy meters, EM24 for the Grid Measurement and an ET340 for the GoodWe Inverter: Both are connected parallel to one...

Like that, no matter which version of the software I use: I'm connected through the USB-RS485 (RJ45 Connector) with the WNT Board. The Drivers are installed well and working, right COM-Port, I have only one. What version do you mean? Where can I see it? When I oredered the Interface Board...

Everything looks fine, in the ESS: Inverter Settings: Charger Settings: The Inverter is not yet connected to the Grid, maybe thats the reason? Do you have any suggestions regarding my voltages?

Interface Board or BMS? When I connect to the interface board, the program says connected, but no values are shown...

Will try it with an new Image in the next days, will let you know (y)

@GRV0423 Ok, i created the cable like that now and the packets are counting up now: (y) But in the Device List still no BMS visible: Any Idea what I else need to do? What abot DVCC? Turn ON or keep OFF? Here is how my Setup looks like:

Ok, it runs now for some days and it looks good now, only really bad Weather now, today snow, so not much Energy from the Sky: I ordered now an ET340 for the GoodWe Inverter to show them up in the overview. I set the EM42 to Address #2, I assume the ET340 will be on Address #1. Then I can put...

You need at least an GX-Device, Cerbo GX or an Multiplus II GX.

That did it! (y) Now I could read out the inverter settings and you won't believe, they set VOLTRONICS+CAN, not VICTRON+CAN.... ?‍♂️ I set now VICTRON+CAN and voila, it is visible in the device List! Now I have only one problem, the Victron runs directly from the Battery and is consumpting...

That one is from me ;-) Does not work. I set the protocol, but no change.

Hi fips, I did that and everything above, but when I log in into ssh and enter "1234" as passwort it says "Permission denied", can you provide me an acual password hash for "superuser" or something like this, please? I'm using the OrangePi-3-lts Image, there is no cmdline.txt in the boot...

I'm trying, but the Daly Support makes not easy for me. I have no idea how to program the Victron Can Protocol. They communicate together, but they don't recognize each other... :(

No, I'm not. Only the Meters are connected to USB through an 5m RS485-USB Cable, that what Victron prefer. And the BMS is connected via CAN. Pin 4+6 of the Cable is the 120R Resistor, but where to connect it to? To which of the two meter and which pins?