Search results

Look for Outback Skybox revival story thread. You need to fool skybox to turn on with a board designed by Sollap

Probably paid less when ordering from China.

Mine are three years old and doing fine !

I bought 16 280eve a year and a half ago from Amy Also bought a JBD BMS that I had problems with After sending pictures and her promising to contact JBD she left me Hi and Dry So I wouldn't use them again!

You don't need the Envoy to make them work. Green means its working.

Hey Sollap Is the Skybox still working? What is the value of the inductor you used? Thanks

The Fet control set to 5 seconds is probably to low, the default is 17 hours

You need a Uart box and laptop You unplug Bluetooth module and plug in the Uart box Then you have more options then phone app I bought mine from Overkill

Amy Zheng Docan

I completely agree with Alkaline But they will still sell plenty of batteries here but not to me I have dealt with Amy on WhatsApp on other issues and she was not very helpful !

Good luck with Docan, I had problems with a JBD BMS from them and Amy wasn't helpful at all !!! I am sure the batteries I bought from them over a year ago are grade B I won't use Docan again.

I do my AC coupling on the load side The Radian will frequency shift lowering the output of the panels if its not needed

Outback Radian 8048 It will AC couple and battery backup

Setting for 30 days did not work The max is 65000 or 18 hours I still would like the BMS to not go into sleep mode or Fet ctrl time set Any ideas? Thanks

Has anybody change the sleep time on a JBD-AP20S003S-L20S-200 or other JBD BMS with UART to USB module? What I want is to turn it off, so it doesn't go into sleep mode. I set it to 0 from 65000 and the relay just goes off and on Now I set it for 30 days, but would really like it off. The problem...

I checked yesterday and that's the problem, right on the minute the relay released and it went to standby power consumption Radian went Ito charge mode, then relay closed again. Does anybody know how to set this? Or turn it off ? Thanks

Sunshine_eggo Do you think it has to do with idle time setting of 65000sec ? JBD says it settable , but not Sure where or how to do it Thanks

Good luck with a warranty claim from Docan I emailed with Amy last night, I have a JBD 200 amp 48 volt BMS that has a intermittent 2.5 voltage drop across the solenoid Causing my Radian inverter to charge every day when it doesn't need too. She told me to send her a video and she would send it...

Has anybody with the newer style JBD BMS with relay had the same problem? I bought it from Amy from Duncan and doubt they will warrant it.

Yes it just did a charge and voltage is back It happen at least once a day. the BMS always shows the right voltage the Victron and my Radian show lower, when its acting up The Radian wouldn't be charging normally but the voltage drop puts it in charging range

My 16s 48 volt 200amp JBD BMS is intermittently losing 2.5 volts across the solenoid This one is a year old, I see the new ones don't use the solenoid anymore they use a relay Anyone else see this problem?

Thanks Samsonite801 I guess I don't understand the "sell Voltage" under AC input Grid. What is its function? My system charges every day for about 6 minutes Battery voltage is around 53.2 and the sell voltage is set at 53.2 Thanks

Could somebody share there Radian GS8048a battery settings with homemade Lifepo4 batteries?

You need a hybrid Inverter, that can AC couple Outback Skybox or Schneider electric our two that would work!

My problem I have 6.4 KW of enphase micro inverters grid tied I have a Outback Skybox grid tied with a loads panel The Outback has tripped and shutdown 27 times in the last 6 months with Gate faults Usually when it trips the grid power is spiking like at 11:29 today, shown in attached file My...

Where did you find log entries in the installer toolkit? I can't seem to find them I can do the Envoy.local/datatab/event...... and get it, but idont see it on the toolkit app Thanks

Could you give me the line filter part # Thanks

I bought that Amazon Battery switch that showed 12 to 60 Volts Underneath the switch it reads Max 48 I am not using it, I emailed the seller with that they never responded.

I ordered a JBD 16s 48v 200 amp BMS today from Amy, I think she has 10 in stock in Houston

I put a 86.74 amp and 4422 watt load on inverter IT read 50.9 volts before BMS and 50.99 at inverter a 0.3 drop Inverter showed LBV 50.58 It lasted about 4 min I can't think of a way to simulate a 130 amp surge Ill try again tomorrow and find more amps to draw, but it seems like with this load...

This morning at 8:08 AM I had a Non Recoverable Fault Preceding it was a DAB-UVP Battery fault again than a Gate Fault As RCinFLA asked I reset lowest battery voltage, it was 40.65V So does this prove its the cables or BMS ? Thanks

So my BMS and cables can't take that type of peaks, ill have to try and fix that Still have to figure out what event is causing it to demand that much from grid or batteries. I am not seeing high loads or high or low voltage from the grid at the event times, looking at Optics Maybe it to fast...

The large transfer switch is from the main panel to the input on the skybox and the bypass breaker on the sub panel The normal breaker is coming from the Skybox load output The 4th picture is the Skybox BAS for wiring inputs I have a normal Enphase combiner box outside.

I jut reset the high and lowest battery voltage, they went to zero but they didn't stay at zero. Before the SC- non recoverable fault shutdown I had 6- PCS-NPC Gate faults 2- PCS DAB FPGA trips 3- PCS-DAB UVP Battery faults I was averaging 8 cleared PCS faults and Can Communication failures a...

Thanks for your replies I did the install on the solar panels and Skybox The Enphase combiner box feeds the sub panel to upper left 40 amp breaker The feed from the Skybox comes into the sub panel lower right 50 amp breaker 6 gauge wire Bypass box so inverter fails I can still run load sub...