D
DC_Ripple
New Member From East Coast
- Joined
Latest activity Postings About Most reacted threads Most reacted posts
-
-
DDC_Ripple replied to the thread Eco-Worthy 5000w inverter in a She-Shed. Grounding is my enemy..Menu Item 63 "N-G Automatically connect" I am glad to read this. I have not powered up my same inverter yet. Still finishing up the...
-
DDC_Ripple replied to the thread 1/0 to 4 awg splice?.So after getting some very good suggestions, I decided against using the reducers 1/0 to 4ga. [of course after I ordered them.....] I...
-
DDC_Ripple replied to the thread 1/0 to 4 awg splice?.Holding the manual in my hand and it doesn't state those models any longer. (older manual on the website did) ECO5000W(SR)-EU and...
-
DWhat I do now in most every case be it going up or down with big wire is use an isolated two stud terminal bussbar type set up…stack...
-
DDC_Ripple replied to the thread 1/0 to 4 awg splice?.There have been a lot of recent posts about the E-W 5000w inverter. Seeing as how no one else has mentioned this, I will just assume...
-
DDC_Ripple replied to the thread 1/0 to 4 awg splice?.I was trying to see how others handled this problem. I have never read about this before. I was looking at several options while the...
-
DGet some big heat shrink and that rubber tape I mentioned. Make the splice about 50% larger than the original diameter of the cable to...
-
DThen use the 2AWG and be careful to get all the strands in there. 4AWG is just too thin. I know it doesn't solve the issue you posted...
-
DDC_Ripple replied to the thread 1/0 to 4 awg splice?.I have the hex dies, 1/0 to 4 AWG
-
DDC_Ripple replied to the thread 1/0 to 4 awg splice?.Yes, I have crimped the 1/0 for the Shunt and Class T fuse holder. I would heat shrink everything. I would only be using a few inches of...
-
DDC_Ripple replied to the thread 1/0 to 4 awg splice?.The Inverter shipped with 4 AWG wire. I tried 1/0 through to entrance hole and it will not fit. I had a piece of 2 AWG, but that seemed...
-
DDC_Ripple replied to the thread 1/0 to 4 awg splice?.These are way more cost effective...
-
DDC_Ripple replied to the thread 1/0 to 4 awg splice?.I was thinking something like this...
-
DJust getting all the pieces ready to start connecting my E-W 5000w Hybrid Inverter. I have 2 E-W 48V Batteries. Class T fuse and Smart...
-
DDC_Ripple reacted to SolarUKWM's post in the thread Waveshare RS485 & multiple Victron VE with
Like.
I'm sure there's a lot of questionable BMS firmware out there. But this is the point ... the BMS is in the best physical/electrical... -
DDC_Ripple replied to the thread Waveshare RS485 & multiple Victron VE.I don't have SA at the moment, so I cannot comment. Just saw the option to connect to the BMS. Agreed, the Shut is the most accurate...
-
DDC_Ripple replied to the thread Waveshare RS485 & multiple Victron VE.Just adding this so it seems possible: Adam De Lay's video show Battery drop down and select USB Victron VE Direct. You must be...
-
DDC_Ripple replied to the thread Waveshare RS485 & multiple Victron VE.Thanks! Reading your post the other day is what prompted this discussion. Was happy to hear you had success.
-
DJust getting started with a Eco-Worthy 5K Inverter (white unit), 2 EW 100ah 48v batteries. Ordered a Victron SmartShunt and T-class...
-
DDC_Ripple replied to the thread AC Connection and limits.ECO5000W(SR) 120VAC 41.7A MAX AC BYPASS 63A MAX CHARGE CURRENT 100A Based on the nameplate info, HYP4850U100-H, per page 9 of the...
-
-
Loading…
-
Loading…
-
Loading…
-
Loading…