Most reacted threads

Are there any hybrid string inverters available in the 6KW range with multiple MPPT trackers? I am planning an array with multiple faces, and want to maximize performance and also improve shade mitigation. I am interested in utilizing the PV power as much as possible, especially during power...

How do the 6000XP modes correlate to the 6500EX modes? I used SUB mode with my EX, where the priority was explicit. Can the XP be set up to operate this way, and how do you do it?

I have an EG4 6500EX-48 and want to replace it with a Victron Multiplus II 5kVA, but I want it to work the same way. I mainly use the EG4 for grid backup, but have a small amount of solar and use it to augment the grid. Unfortunately, the idle consumption of the EG4 eats up most of the power...

I have a new problem with my 6500EX-48. I can no longer enter User Settings. If I hold the ESC button down for 3 seconds, it enters the settings mode, but then displays a fault triangle warning and a red fault indicator. No fault code is displayed. I can go back to other functions, but I can't...

I just fired up my 6500EX-48 and after a few minutes I get a frequency readout of 61Hz and a flashing fault light.

I just installed my new inverter, along with a LifePower4 battery with BMS connected. The battery icon is flashing indicating BMS comms should be good. After charging the battery, I got the F69 fault code. Should I be concerned about this? Should I just reboot everything?

I just ordered a 6500EX-48 and LifePower4 battery from Signature. The battery shipped immediately, but the inverter is on back order. I called and talked to sales. They said it was because they are upgrading the inverters, and it might delay shipment for "1-2 weeks". Has anyone heard about this...

I wanted to feed an essential loads subpanel with the output in EPS mode, but since the loads would be all over the house, I want to make sure that the unit will protect itself if there is a fault of some sort on any of the load circuits. Does anyone know what kind of protection the AC outputs...

I want to track down a BMS error that I'm getting to see which cell(s) might be overcharging. I can connect to the battery without error, but when I open the BatInfo tab, it won't populate the table. I have Adr 0 selected on the battery and the app, and the battery is isolated from the system...

This generator has a connector to interface with a "compatible" ATS, but nobody at Duromax seems to know anything about it. I assume that this is much like the ST Switch connector on some Westinghouse models. Since it has 7 pins, I assume that it allows more control than just an external Start...

Here's more data to add to the idle consumption debate on this inverter. My 6500 is only a couple weeks old and has firmware ver. 79.63, and the battery is one LifePower4. I am using the USER battery setting because with BMS comms enabled, I get a F69 error. I think this is because one cell or...

I have a EG4 Communications Hub that I'm trying to get to communicate with Victron can bus. The hub is talking to the LiFePower4 battery just fine using RS485, but I can't get the battery/hub to show up in the Cerbo GX device list. The hub is set to Victron CAN protocol, and the hub is connected...

Does the "advanced" MPPT of SMA or Fronius really work? I am interested in a string inverter, preferably DC coupled that I can use with a variety of batteries, and I want to keep things simple especially on the roof. But don't want to suffer too much from morning or evening shade which could...

I am happy with this inverter except for the high idle consumption. I am averaging a bit over 120w. I mainly use this as grid backup. I am limited in my amount of PV for a number of reasons, and on a good day I can just make up for the inverter overhead over a 24 hr period... about 3kW. Most of...