Most reacted posts

Thanks...(y)

I was reading your problem and how did you solve it, very well done...I wonder if to activate the SOC mode in the inverter you have to have the batteries in close loop or can it be done in open loop?...I have the problem that when I sell to the grid it pulls the batteries... I have them in open...

I understand Schneider does not recommend it for the XW plus... but they were able to solve the problem that the previous version had, it works very well in the XW Pro...

ok...let me see if I understand, I have to discharge the battery to its lowest point and then fully charge it and then the bms will register the % of soc... Yesterday I tried to put the values, of the battery, back in I have turned off the bms settings, restarted it and nothing... JK should have...

Greetings to everyone in the group...I want to learn about my renewable energy system...I have been monitoring my Schneider 6848 system because it has a lifepo4 battery pack and my JK bms installed. I have noticed that the voltage indicated by the SCP (54.4v) is not the same as that given by the...

Thanks.... (y) (y)

That when I sell to the grid I don't draw amperage from my batteries

:)

I have not installed it yet but I have met friends who have done it and their comments have been that the new version corrected the problem of the previous one.

hi...I only have the JK-BMS RS485 adapter...where do I get the TJA1050 CAN module and how do I connect it to the ESP32 to the inverter's CAN port. I'm very interested in learning and being able to integrate the JK bms into my Schneider inverter.. .Thank you

I have a lifepo4 48v ...360ah battery bank with a 2amp JK BMS, I'm thinking of installing a high-current (5A) flying capacitor balancer. I've read that it can balance them faster... could you tell me if what I want to do is right? .....Thank you

Hi...ok I understand your part, you have to have some skills and knowledge, I thought it could be less complicated. Thank you very much for the time you took with me explaining the steps and what I would need. I ask you, is there any BMS on the market that is recognized by the Schneider inverter...

Has anyone had any experience with the 4th generation Neey balancer?...I've read that they made changes to the application and the parameters....thank you

Thanks... (y)

Hi...I was wondering if you had found a solution for this problem, I have a JK bms and by changing some settings and the soc % changed from 100% to 78%. The battery is fully charged at 54.4v...how can I get it back to 100%...

Hi....A few days ago I did a firmware upgrade to my XWPro 6848 from version 1.03 to version 1.11 through insight home. Everything seems to be working fine except that the lights that indicate the battery charge on the inverter panel stayed off... I have no idea how to turn them back on...

Hello... could you explain it in more detail, I have the adapter for the can port and the RS485 but I can't get it to communicate with the Schneider pro inverter...thanks

Hi....could you share the parameters you used?...it would be of great help to me...thank you

Greetings, all that information discussed here is very interesting. I would like to know if all this information about the JK bms can be applied to the XW Schneider pro inverters to be able to see it through the insigh home. I have searched without much luck to be able to integrate my JK bms to...

Hi... I need the help of the group.A few days ago I upgraded the firmware from 1.03 to 1.11 to my XW pro following the steps of Schneider, first I updated the insight home and then the XW pro inverter. The update was done well but I find the detail that when the grid is absent the red led that...

Hi......I need your help...a few days ago I upgraded the firmware from 1.03 to 1.11, to my XW pro following the steps of Schneider, first I updated the insighthome I put the inverter on standby and then updated the XW pro. The update was done well but I find the detail that when the grid goes...

Hi.I was reading your problem and how did you solve it, very well done..Could you give me a guide on how you solved the problem so that the system does not deep cycle the battery? I have tried with Schneider technical services but they do not have the answer... thanks

Ok...what I mean is that it's stuck with the three little lines on the screen and it doesn't want to sell to the grid or go into self-consumption, it's stuck in AC passthrough. When I turn off the grid it starts to feed on the batteries. .The Backup mode is enabled.The battery voltage is...

:)

Hi......I need your help...a few days ago I upgraded the firmware from 1.03 to 1.11, to my XW pro following the steps of Schneider, first I updated the insighthome I put the inverter on standby and then updated the XW pro. The update was done well but I find the detail that when the grid goes...

Ok...could you send some screen shoots of the changes you made...I don't understand, my battery does not close loop but I must activate the SOC mode for it to work correctly?...excuse my lack of experience in this

The first step is to set the capacity of the battery, which is what the capacity of the battery would be. You can set it a little larger, for example, 100AH battery capacity, 120AH or 150AH battery capacity. The second step is to discharge the battery through the discharger, discharge the...

I have XW 6848pro recently entered the program to sell to the grid... I have tried to make adjustments based on the manual and what technical support tells me but I always see that the inverter draws a lot of amperage from the batteries. I have seen that some here have had this problem and I...

Thanks but the graph is not clear, even if I zoom in

Two CC Schneider 60/150....5.9K in pv