TomC4306
Solar Obsessive From Maryland, USA
- Joined
Latest activity Postings About Most reacted threads Most reacted posts
-
-
TomC4306 reacted to Quattrohead's post in the thread 280Ah cells with low capacity - can I still use them? with
Like.
Separate BMS and then join them together in parallel. -
TomC4306 reacted to Dinobot248's post in the thread Advice on installing large off grid system. with Like.
Here is my 2 cents. This is a lot to unwrap. Leveraging your “guesstimate” numbers 3,000 kWh / month equates to 100 kWh / day and 4...
-
TomC4306 reacted to timselectric's post in the thread Recommendation needed, plz. PV & Battery monitor for off-grid. with Like.
10 more votes for Solar Assistant. I never want to be without it, again.
-
TomC4306 reacted to Crowz's post in the thread Recommendation needed, plz. PV & Battery monitor for off-grid. with Like.
Solar Assistant is the best monitor you can get if its compatible. If its this one ...
-
TomC4306 replied to the thread Chinese inverter discharges batteries without anything connected.No, you don't have the settings set correctly. User error.
-
TomC4306 reacted to NCislander's post in the thread New Solar Assistant beta 2024-04-05 and stable 2024-01-23 software released with Like.
"Pulled over by a Cop, Excuse me sir, Have you been Solar Configuring while driving this afternoon? That's a confinement from Solar for...
-
TomC4306 replied to the thread New Solar Assistant beta 2024-04-05 and stable 2024-01-23 software released.Mine does.
-
-
TomC4306 reacted to timselectric's post in the thread Battery Blues : first Li Time now SOK with Like.
I've never understood the fascination of worrying about BMS security. How many enemies have you made? Or do you believe that random...
-
You’re way overthinking this. Gas masks? Lifepo4 is just as safe as lead, especially AGM batteries. For a simple 24 volt 100ah...
-
TomC4306 reacted to Rich V's post in the thread LiFePO4 16S 48 Volt Standby Battery Voltage with Like.
I have an Outback system using SOK batteries setup similar to yours. My system On a daily basis my batteries are only charged from the...
-
Your battery is ruined. A charge controller will limit current or turn off when the voltage goes above the bulk voltage of the battery...
-
Because the BMS has protection settings that disable charging you will find 14.6 volts is too high. The battery enters protection and...
-
TomC4306 reacted to plympton's post in the thread The Will 3000 Hand Truck System, 2024 CES, Started buying used panels 3 years ago.. with Like.
🤐
-
TomC4306 replied to the thread The Will 3000 Hand Truck System, 2024 CES, Started buying used panels 3 years ago...Will's 3k inverter is ~ $700. Weighs about 25 pounds. Sol Ark is ~$7000. Weighs about 200 pounds. So, I don't think it is remotely...
-
I think i maybe have finally an explanation,but correct me if iam wrong. The scc reads the battery voltage CORRECTLY ONLY when not...
-
You are using two different voltage indicators on either end, not a voltage meter. The difference being, a voltage meter would be...
-
TomC4306 replied to the thread 10w lost. But where???.Measure each with an independent meter. DMM. These devices are not NIST calibrated.
-
There will be voltage drop in the wiring, so the higher potential source, the SCC will have higher voltage on its terminals than the...
-
TomC4306 reacted to Texas-Mark's post in the thread LiFePo4 charge problem after reassemble. Any help? with Like.
Yes for the first No for the second. I really think the issue is that you never fully charged the battery. The difference between 40%...
-
TomC4306 reacted to Texas-Mark's post in the thread LiFePo4 charge problem after reassemble. Any help? with Like.
Sounds like it was not charged to 100% if you were going by voltage change.
-
-
Loading…
-
Loading…
-
Loading…
-
Loading…
