Hello Forum, I am building a 250A précharge due to the fact I am corona bored.
The is nothing else to do.
Here my project. It is a test board, sorry but not perfect. Using hot glue to makes things stick.
To power my précharge circuit I am using a battery pack. Here my parts.
For the delay...
Dear Forum,
I have purchased 4 Lifepo4 cells 200Ah Grade A from N.... Official Store.
When I opend the box the voltage level was
Cell1: 3,271V
Cell2: 3,274V
Cell3: 3,271V
Cell4: 3,273V
Then I paraelled them and charged the up to 3,65V and rested them. Current dropped to Zero
I did Top...
Hi I have bought this Current Voltage meter as well that Will uses as well.
The voltage display is 0,3V off the battery voltage. Do you have made the same experience. It this unit displays internal voltage incl. internal voltage drop off powering the coil
Used external supply. No difference...
Dear Forum,
I want to convert a gasoline Race Kart to an Solar Green Kart.
I have two panels a 100W. 20V on hand.
One panel will be used as a rear spoiler and the 2nd one shading the driver.
Here my question.
I want to power the Kart with scooter battery packs. 48V.
I like to run the...
Hi Forum I have bought the Daly Smart 40A BMS. I have downloaded the APK but the translation to German it terrible.
I assume the US APK Version is much better. How can I change the APK language or do I need an different apk.
The Version I am using is V 1.7
Then the.adjudtment of SOC is not...
Hello Forum,
Questions to my RV system.
I have an inverter 12V/DC 230V AC
2000W.
Wabt to build a Higee 12V 120Ah pack from BLS. My budget is limited.
Cell pack is 420$.
Will you Lifepo4 Higee can work well.
The spec sheet only listing 120A continues.
My inverter can take up to 166A and with...
Hello FOLKS,
Short question, does the housing of a Lifepo4 battery cell has a potential.
The means und the blue plastic is the AL case. Is that isolated or does it has a potential. Who knows about this?
Greeting Bob
Dear all,
thank you for your advise in advance. US goes green again. Looks like solar gets a push.
I using a 2000W Inverter in my RV who is used temporarly and most of the time is off by remote switch.
I am struggleing want to start a DIY project to power my RV with 300W Solar on top.
I...
Dear Forum,
I have seen this QUCC BMS. What I like about this is the heavy bus bars.
The SMD design looks well arranged and the quality looks acceptable.
The only downside is the low voltage cut off. 2.2V per cell.
I am thinking of buying this unit
Hope it is not a bummer.
Good day
Bob
Hello Folks, Girls and Men's looking for a BMS for a 20s Setup. 72V out of 18650.
Current max continues is 2c of 2900mA
I have 400 Lions 3.7V available.
I have already the contacter gas filled and Mega fuses.
So I thought to go entry dollar level.
Seperate Port.
20s in series is 84V but the...
Need a discharge protector cut off 50V-60V programable to operate a 12V contacter.
I want to protect my batterie against Low Voltage discharge.
I am not using a BMS. Using an IDST 8S charger for balanceing.
My pack is 72V and I am using a 12V 250A contacter to switch the load.
Now I want to...
Hello,
I am located in Europe that why 230V 50Hz.
Question what is the most common panel system voltage?
From the panels shall I use a victron MPPT 100/20 for charging my battery bank.
Is this the right way to go.
And from the bank running an inverter to 230V.
Or do I need a BMS in between...