Anyone else with a recent EG4 48v Lifepower4 battery purchase getting a "Charging MOS fault alarm" that can't be reset?

[Wolfpack7483]

Got my battery last week, but today was the 1st time to get a full charge on it. Everything was great @ 99.6%, cells balancing, current curtailed, but I had to leave. Got back about 1 1/2 hours later to the beeping & red light associated with the fault. Re-set didn't work & I couldn't find anything online about it. Called Signature Solar support, and they said this has been an issue with a recent batch of batteries. They asked me to open the battery & send them a picture of the CMOS, to make sure it wasn't a real fault. It wasn't, & they sent instructions to go into the config tab and enter a settings change in the "reading and writing of MOS adhesive fault codes" That did the trick, just hope it doesn't come back again in the future.

 

[marionw]

Could you share what change you made on the "Config" tab?

 

[Wolfpack7483]

Attached are the instructions they sent me.

 

[marionw]

Thanks. As soon as I read your post I did mostly what you did (before you provided the response). I already knew the password.
I first read all the other batteries and the "reading and writing of MOS adhesive fault codes" was 00.
For the failed battery I entered FF set it, then read to see if it took, it did. I then entered 00 and set it then read to see if it took and it did. Now it reads the same as the other 5 and the alarm has cleared.

The CMOS and DMOS are now both on and the battery is taking a charge. You saved the day.

Thanks for the post...

 

[DBarr]

Dbarr Issue: 04-01-24 (Not an April fools joke)

EG4 PowerPro4 48v100Ah Battery SOC low Alarm

The batteries (Both attached in parallel) voltage dropped to 51.2v and caused an alarm light to flash.

The Fix: Charge batteries up to at least 53v, then turn breakers off, unhook batteries from everything, push “RESET” button. Then turn batteries back on one at a time to make sure everything is working. Turn breakers off; Hook everything back up, Turn breakers on one at a time.

Looked into forum for posts similar, tried the MOS rewrite with no success and the above is what worked for me.
(Note): I just received the two EG4 batteries less then a week age and have them to recharge my EcoFlow Delta Pros.

 

[Cotbone10]

Attached are the instructions they sent me.

Thank you for posting that! Didn't work the first time but did a couple resets then it worked!

 

[CableGuy]

Got my battery last week, but today was the 1st time to get a full charge on it. Everything was great @ 99.6%, cells balancing, current curtailed, but I had to leave. Got back about 1 1/2 hours later to the beeping & red light associated with the fault. Re-set didn't work & I couldn't find anything online about it. Called Signature Solar support, and they said this has been an issue with a recent batch of batteries. They asked me to open the battery & send them a picture of the CMOS, to make sure it wasn't a real fault. It wasn't, & they sent instructions to go into the config tab and enter a settings change in the "reading and writing of MOS adhesive fault codes" That did the trick, just hope it doesn't come back again in the future.

same on my 2 batteries, first time i'm charging them. got them in february, so they sat for 2 months but still reported 2/4 LEDs SOC.

i dont have time to pull the batteries from the rack right now. is the inspection needed? what would cause a false alarm?

 

[Wolfpack7483]

I think it's likely that most are false alarms. The inspection is to see visually that the mosfets aren't fried. If the setting change works, I'd think everything should be OK.

 

[Cotbone10]

same on my 2 batteries, first time i'm charging them. got them in february, so they sat for 2 months but still reported 2/4 LEDs SOC.

i dont have time to pull the batteries from the rack right now. is the inspection needed? what would cause a false alarm?

I didn't do the inspection, just did the reset. Figured if that didn't work I would do the inspection. Mine was caused because I didn't have the most up to date firmware on all the batteries. Was mixing firmware unknowingly. Signature Solar doesn't do a good job at instructing new buyers to update firmware after purchase and before install...

 

[SignatureSolarJess]

Signature Solar doesn't do a good job at instructing new buyers to update firmware after purchase and before install...

Hi! I just wanted to pop in and clarify, we really don’t recommend immediately updating firmware after purchase/before install as it could possibly cause it to stop functioning, becoming a brick. Basically, we advise that unless there is an issue, don't adjust the firmware.

 

[marionw]

If you are not running Version 3.37 firmware (have an older one) and you are using an EG4 Communications Hub you will need to update to v3.37 as the firmware update increased the baud rate on the pins 7&8 RS485 port to 19,200 which is what the BAT Input on the Hub requires. This increased baud rate becomes even more important as you add additional batteries to your stack.

 

[Brucey]

Hi! I just wanted to pop in and clarify, we really don’t recommend immediately updating firmware after purchase/before install as it could possibly cause it to stop functioning, becoming a brick. Basically, we advise that unless there is an issue, don't adjust the firmware.

Is this advice limited to the eg4 batteries or the aios as well?

 

[SignatureSolarJess]

Is this advice limited to the eg4 batteries or the aios as well?

We advise not to adjust anything unless you're having problems

 

[Cotbone10]

Hi! I just wanted to pop in and clarify, we really don’t recommend immediately updating firmware after purchase/before install as it could possibly cause it to stop functioning, becoming a brick. Basically, we advise that unless there is an issue, don't adjust the firmware.

That's what I was told as well by SS technical support. However, when you purchase batteries at three different times months apart the firmware differences do cause issues. Maybe a general training at SS needs to occur to address these different case scenarios? Then the sales staff could pass on that information to returning customers, like myself.