Pozdravljeni.Pravkar nalegam na 3 inverter je spf5000es firmware 067/068-f4-a27.DELUJE.Sledite priloženim navodilom pa bo OK.. HVALA MOJSTRI... ????Pozdrav iz Slovenijeali ste prebrali navodila za flash, ki so priložena datotekam vdelane programske opreme, in kako napajate pretvornike med flashanjem?
Looked like your com board requires CP210x, and you said it did not work. Then as what “kirkdis” had stated, perhaps you need to change your laptop/computer too. For identification of com board and applicable usb driver, please see:yes I have read through. didn't do anything else.
power was supplied by the battery.
i have two machines one is a [067 01 1.04 / 068 01 1.04] and i was able to do a firmware update successfully to [067 F4 A27 / 068 F4 A27]
the second machine however [113 00 9.07 /114 00 9.07] could be a problem. has anyone found an update that will fix the fan noise issue?
he used a macbook and emulated windows. I told him to change to native windows and he got it somehow managed to flash the firmware.Looked like your com board requires CP210x, and you said it did not work. Then as what “kirkdis” had stated, perhaps you need to change your laptop/computer too. For identification of com board and applicable usb driver, please see:
https://www.amosplanet.org/how-to-upgrade-off-grid-inverter/
If you browse the above website, you may even see the appropriate procedure and required files for your update.
if you use can or RS485 communication and your bms is sending SoC values the inverter will change for several settings to percentage. this is not clearly mentioned in the manual but it is like that. You need to change setting 5 to USE or US2 then you should get back your voltage settings without letting the BMS fully manage your battery...Hi Everyone!
Thanks for you and this forum I also successfully upgraded my crazy fan 5000ES
It works fine, but now I found a change in settings which is for me a bit frustrating.
The settings 12 and 13 were settable as voltage level of battery.
In the new FW these changed for percentage (%).
This would be ok, but previously I could the back to utility set till 46V (48V batt), which is low enough to set the battery cut off so low how I wanted.
In the new firmware the minimum percentage is 25%, which is to be honest a bit high for me. I would set it to 20, might 15 not decided yet.
Is it possible somehow?
Anyone faced the same problem?
Thank you!
Ferenc
seems like the communication is shortly disconnected or not setup properly. Try to contact the vendor or the battery seller and ask for compatibility to pylontech or especially compatibility to growatt inverters. They should be able to tell you what communication protocoll to use.hi everyone
I am having similar but different issue,
set up is 4 SPF5000ES inverters running on 3 phase with 6 48v 200ah battery's 2 inverters are running on p1 the other 2 are on p2 and p3
in sbu mode inverters work fine until the battery's get to 50 keep getting a 04/ low voltage error and keeps charging battery when set to Solor only then trying to drain from battery's is similar if not same issue as kirkdis seen his YouTube video (# kirkdis couple of views where mine lol)
how ever when check the voltage of battery all 6 are near 50% mark and have more that enough power to keep feeding loads here is some pics of issue as can see the inverter all over sudden thinks the battery's are at 1% then shoot up to 47 and get stuck in that loop and have to change it
this is set up as a solar/grid
settings
01-SBU
05-LI- 36-Protocol-51
12- 20%
13-60%
01 uti ( but I use a contactor via dry port to switch AC in)can we have a look at the settings you guys used
01, 05, 12, 13, 19, 20, 21 and 36
are you running an off-grid, grid backup or solar/grid setup
Mine is...can we have a look at the settings you guys used
01, 05, 12, 13, 19, 20, 21 and 36
are you running an off-grid, grid backup or solar/grid setup
In addition to "kirkdis" recommendation, you may want to browse thru below website which contains the battery-comaptibility list for SPF5000ES, amongst other things:hi everyone
I am having similar but different issue,
set up is 4 SPF5000ES inverters running on 3 phase with 6 48v 200ah battery's 2 inverters are running on p1 the other 2 are on p2 and p3
in sbu mode inverters work fine until the battery's get to 50 keep getting a 04/ low voltage error and keeps charging battery when set to Solor only then trying to drain from battery's is similar if not same issue as kirkdis seen his YouTube video (# kirkdis couple of views where mine lol)
how ever when check the voltage of battery all 6 are near 50% mark and have more that enough power to keep feeding loads here is some pics of issue as can see the inverter all over sudden thinks the battery's are at 1% then shoot up to 47 and get stuck in that loop and have to change it
this is set up as a solar/grid
settings
01-SBU
05-LI- 36-Protocol-51
12- 20%
13-60%
hi that what I thought but when the inverter disconnects from comms inverter would disconnect loads and reconnect when back up and that not happening its more shortly percentage drop to 1% then because its to low the inverter charges it then goes straight back up to 47% starts draining and feeding loads looks fine then drops back down to 1% and repeatsseems like the communication is shortly disconnected or not setup properly. Try to contact the vendor or the battery seller and ask for compatibility to pylontech or especially compatibility to growatt inverters. They should be able to tell you what communication protocoll to use.
For Pylontech compatible BMS settings in the SPF are LI and protocoll 52... maybe that helps!
Will this work on the 230v version or is this intended for US model? Current firmware 067.01/068.01.If the firmware in the picture above is what you had, you need to update with this firmware.