That's 11,280w. So either something is different with that inverter or my inverter has been the issue all along.In my video im not using anything no soft start at all. 1x18k No Grid and the 5 ton Self Contained Unit. I dont know what else to say.
Did we replace your inverter already I can’t remember and the surge was 147 amps if you look at the bottom of the meterThat's 11,280w. So either something is different with that inverter or my inverter has been the issue all along.
No I'm still fighting same inverter you changed firmware on in October. Would shut off the whole house trying to start ACDid we replace your inverter already I can’t remember and the surge was 147 amps if you look at the bottom of the meter
I will have someone contact you for a RMA. I want to personally test your inverter when it comes in as well I can post the results here if you are ok with that. After you get a new replacement and this problems is still going on what would you suggest the problem is at that point?No I'm still fighting same inverter you changed firmware on in October. Would shut off the whole house trying to start AC
So at 147 I really have a POS then
I have know idea. I know I ran the same setup with 2 6548's and not once did the AC not start for 2 summers. When I first installed this inverter it shut down trying to start AC. Now after numerous firmware changes it will run AC.I will have someone contact you for a RMA. I want to personally test your inverter when it comes in as well I can post the results here if you are ok with that. After you get a new replacement and this problems is still going on what would you suggest the problem is at that point?
Damn, that looks almost identical to mine. When you say "lights flashing" is that only during the start ramp or do they continue flashing following the start on the run cycle?I installed a new Micro Air today. The start amps are 32-33 amps now. But the light show I get everytime it starts is not good. So I'm not sure what is up but when I was on 1312 I use to get big blink on a hard start. Now I have 10-15 amp less hit and the lights flashing is terrible
Only flashes/blinks when AC is starting. Now that I have the AC start amps lower then they have ever been, I would have thought it would have been better. But I was on 1312 firmware before, and now I'm on 1616. Before, it was a blink/flash. Now, it is multiple blinks/flashes.Damn, that looks almost identical to mine. When you say "lights flashing" is that only during the start ramp or do they continue flashing following the start on the run cycle?
I'm still curious how you got 2x the rated output of the inverter. 12,000w at 1.35% is 67.5 amps. Can you explain?In my video im not using anything no soft start at all. 1x18k No Grid and the 5 ton Self Contained Unit. I dont know what else to say.
It’s a surge only for 1 sec it’s not continuous. Have you tried to use 1919 you can update with your phone.I'm still curious how you got 2x the rated output of the inverter. 12,000w at 1.35% is 67.5 amps. Can you explain?
Here is what I just tested. Started AC with 6824 w already on. Went to 9884w with AC. Then I turned on a couple burners on oven and it went to 13.5kw. So all is good so far.Were you able to get this ironed out? Lots of 18kpv users on here that may benefit from a potential “fix” or might be happy to know if there was an “issue” found
13.5kW is impressive for the 12k. How long will it handle that load without bypassing to grid? Are your loads well balanced between legs?Here is what I just tested. Started AC with 6824 w already on. Went to 9884w with AC. Then I turned on a couple burners on oven and it went to 13.5kw. So all is good so far.
Inverter was great all winter. Just wasn't happy with my AC and now it seems happy all the time
MY useless comment deleted. By mewithout bypassing to grid
Might try it tomorrow... I removed my micro-air to have it serviced last year. Ill try it on the 18k prior to installing back. the only difference is I'm running a 3 or 3.5 ton I forget.Interesting on the micro-air. I would be curious to try without the micro-air at all. Thanks for the update.
What’s your station name? PM@ksmithaz1 didn't work for me... forgot to update yall here.
Current setup: 18kpv with 20kw server rack and 4/0 cable. The 18kpv shut down and restarted on my three attempts. Also, I have 5kw+ of solar hooked up. I just had the 3.5 HVAC hooked up to give it a fighting chance. I need to try it again and take some readings. Also, I'm off-grid, so no grid assistance.