Search results

https://www.18650batterystore.com/products/envision-aesc-305ah-grade-b-cells-3-2v-lifepo4-battery?utm_content=Facebook_UA&utm_source=facebook&variant=43123829702807&fbclid=IwAR0bHYR_OHjw4dcXJOayTzW-2CpKEy0qN_UEa9d9GJSwbBEqa0KcvsxF4TQ These are now 89.00 per cell. Tempted to pull the trigger on...

It was just doing it. Appareently, it was a known issue from Scheider when you paralleled two 6848's. That didn't stop the company I hired to design my build from building a "wired system" for me to DIY. (Solar Unbound). There was a new firmware that fixed it.

I bought from this guy a couple times. Last time though, in Sept 2022- he never sent me the BMSs I purchased. I wired him $346 and now he's ghosting me. POS.

Been looking for manufacturers recommendations. No luck. What type cells do you use in this orientation?

I'm off grid with two big Schneiders. I can say, my lean, energy efficent washer causes lights to flicker with every little surge. I only say this, because although these are crazy quick surges, they are the only surges that does this. No blinking lights with well pump, air conditioner, etc...

Batrium K9. I replaced the bus bar, the ring terminal, the fuse, the wire, and the ferrule. Same problem. In fact, it is getting worse. It deviates so high I am going critical. I changed much of my critical thresholds to account, but that reduces the level of safety for the system. I just...

Have to have the combox or gateway. You do need extra equipment.

I don't have an answer for this, but I will say, my duel 6848's have given me a couple issues. There was a firmware that, when paralleled, produced 45HZ instead of 60. This is apples and oranges to your problem, I had to search to find out that it was a known problem with a certain firmware...

Steve, Trying to understand the AUX2 Logic Input-2. I tryed with (resisted) 12v signal from the Batrium BMS. The idea was to have the batrium send a 12v signal to "stop charging" when the Batrium Shunt sees 90% SOC. I'm missing something- I put a resistor on both +/- of 12 as a test, but...

I just expanded my system with another 16s bank. I have one cell, #43 of 48 that will jump up or down radically. The entire collection of banks is working well. I have had any problems yet, but this does worry me. Is this a blemished terminal thing? Or a greater problem? Thanks.

I had a firmware issue a while back. Mine was putting out 50HZ.

Disregard. Nailed it. Setting in the BMS. Rookie mistake. Argg...

Hey everyone. I'm using my first Smartshunt on one of my builds. I have Batrium for my big boys that power the house, but now I'm experimenting with smaller batteries for a couple products. Smartshunt is on a 420AH 12v. I did 4P2S (105AH cells). Everything was working well with capicity...

I do not have a drill index. Perhaps I will look into that. I sure don't want to mess it up either, right now I have a valid reason for the company to replace them, sure don't want to make it worst on all fronts.

For sure.

I just got 16 more cells. In one box, a thread from each was not threaded. Smooth inside, with no threading. Speaking to the seller now. The cells appear fine, just overlooked in the construction. I can just thread them myself with an M6 tap... right?

Thanks to all of your help. Walmart did have them. Did. They don't now. I ordered two for my 2 16SS 280AH banks. I went back for more as I'm buiding my 3rd, and they are out of stock on 250A Class T fuses. Thoughts on 225? The largest Amperage I've seen in my entire bank consiting of 2...

Amen! I have just 28KWH in two banks this far. My supplier has been Amy Zheng from Docan. I just can't believe the performance! I built for expansion, and intend on building at least four more banks.

This is just to celebrate how good these things work. I had SLA bank I replaced a week ago. You just can't beat them. No more generator! No more worries!

I'm going to unpack this more and hopefully figure it out. For a novice like myself, that all sounds quite overwhelming. I watched a few of your vids, I feel like a lot of what you're doing is over my head but very interesting. I'll take some more looks. I suppose all that I have undertaken...

Thanks. I needed that. Wasn't quite sure.

Hey. I'm set up now an Batrium is working great. Two Batteries (so far). I have the Watchmon Core and 2 K9's. I'm very apprehensive regarding the intergration. Dummy question: Did the "speak to each other" via Wifii? Or hard connection? Not really sure how to link them. Thanks

The Lifepo4 is completely independent of the SLA at this point, haven't converted... still building. I just have a bench top charger I set for 58.0 volts on the Lifepo 4, just to bring it up as I have had a slow build since top balancing. I brings up the voltage, appears to have added to the...

Perhaps a rookie question.... I have a pretty sweet Lifepo4 battery cart as I prepare for the replacement of my horrible SLA bank. I'm running Batrium with the Watchmon Core, (2) K9s, and shuntmon. Shuntmon appears to be good, but doesn't show a charge. I'm just using a benchtop charger to...

Thanks. I did just place an order. Never looked at Walmart, guess I didn't exhaust my efforts. So far, so good. I have placed 4 orders at places thus far that later called me and said they were out of stock.

recently?

Good call. I had not seen that source. The site said they have them, but I just got off the phone... 250s out of stock. I'm going to spend MORE money and purchase 200AMP fuse blocks (assuming they are in stock, they could not confirm it) Glad for the link for future projects. I learned...

This is horrible. No fuses anywhere. I acquired 3 200As but... My banks should have 250A fuses. If I used the 200s, my blue seas holders do t work. I can't even find holders for the 200a. Argggg! This is holding up my conversation from SLA banks.

Thanks for the info. Question...does the length and gauge of the cable matter? Seems like equal lengths of battery cables matter when you parallel.... But when I have 280ah and 100ah- does my cable need fo be the same length and gauge?

Correct. 3 strings in parallel.

Question.... I'm making a "battery cart", my intent is to make 3 of these when I'm complete. As I put this together, I have two strings of 16S/280AH. I was worried about size/room/weight, so my third string (of this first cart) is 100AH. I've watched vids on youtube where this seems to be...

Damn! that's a great looking battery. Good job! So clean!

Your post has me concerned about my exisiting project. I have two 16S 280 AH strings, due to room- I decided to make a 3rd string @ 100 AH. What kind of problems would happen in this config? You say issues at top and bottom of charge. Can you elaborate? Thanks, James

There's a shortage. Hard to find.

Thanks for the input. I'll confirm the delay with my existing order at the one place. If my suspicion is correct, I'll be cancelling the order today and reaching out to Alte