You have to use a new cat 5 cable, cut one plug off and only use the brown and brown/white wires connected to the correct polarity in the video. Reuse the circuit board end and throw away the two wire ss cable.
Weird, I am using the same setup Pi 3LTS and the LTS file listed on the site. The driver must have been in my file. After changing the pins it would let me change from using 'inverter values to the USB Narada RS485 on port USB USB serial setting.Then go into config advanced settings under the...
Can someone explain how ac pass-through works? Is the inverter outputting when the LCD displays AC pass-through when I connect my generator to charge the batteries or is the generator charging batteries and powering the loads exclusively and not going through the inverter?
The ongoing world events have me finally getting off my butt and wanting to install a backup system. My money, like many, is limited and I will have to purchase the inverter, batteries, and panels in 3 steps. With the prices skyrocketing and shipping going through the roof on this gear what...
So rip out those two small plastic boxes, install larger metal boxes with more room to work, and use two pieces 3.5 long 3/4 PVC between the two thru the wall? Then from inside box to panel with what I call bx cable. How would you do it?.
Worked for me. When I received my inverters, the two black cables were wired differently. I paid no attention to pinouts and cut off a cat 5 and used the brn and brn/wht wires on the circuit board end as the video states, then everything worked fine.
I have two EVG 6500 inverters and two rack batteries and my well pulls almost 40 Amps inrush on each leg when it starts up. It runs the well with solar coming in but I have not tried it at night, batteries only.
Thanks for the link. He says if I read it correctly, that his well pump pulls 1500 watts per leg which is not much at all. May not be a deep well like ours. The main reason for me is to power my deep well and I can't find any examples yet of these inverters powering a 1-1.5 hp submersible pump...
Well, I give up. I can run either inverter on either string of PV one at a time and the AC is steady at 120v. When I connect one inverter to PV, one runs off the battery correctly and one off of the connected PV, voltage is steady on both. I just can't run both inverters on PV at the same time...
Output is still all over the place on solar but 120v steady on battery. It's late in the day with little PV input but it read the same at 1500w PV input, batteries fully charged. From 101 to 146v I've seen.
I have two EG 4 inverters and have only one 120v 15 amp line I can run to it or them for battery charging. I this doable and how would you go about it?.
In S/A config settings is battery type set to user?. I only saw one battery until I set to user.
Battery settings - edit
Battery type
User
Charger source priority
Solar first
Shutdown battery voltage...
Does solar assistant allow you to set/ change battery settings? What manual settings do you use for the batteries? After changing the inverter settings back to USE do I have to manually set the battery charging settings or will the inverters do it correctly? Sorry for so many questions but you...
Is there a rule of thumb as to how many watts of panels to inverter output?. Let's say for example we have an MPP LVX6048 inverter rated at 6000 watts, what amount of PV would be required for the inverter to operate correctly and produce full power?. This inverter has the option to operate using...
"Gen mode". Do you have your generator connected to the AC input? If so what size wire are you using?. I would like to do that as well once I figure out the issues.
Does anyone know the size of the case screws on these inverters? They are too damn small to work with. I am guessing 2 or 2.5 mm and looking for some thumbscrews that will work in their place.
'"On the double pole breaker, 1 pole is L1 and the other is L2, both 120vac. L1 will go to one inverter and L2 will go to the other inverter" This is as Dude says, correct.
"The EG4 setting is what I used to handle all the settings. The only settings I changed were max charge rate to 100 AMPs, Solar only charging, switch to bypass mode at 5% , and return to battery only mode at 10%" Can you elaborate on this setting please.
Is it possible to connect a second LCD screen to the inverter? I see another connection for it underneath and was wondering if one could stay on the inverter and another on a long cat 5 be set in another room for monitoring.
I noticed today when running my EG 4 inverters that are set up in SBU that the AC output varies wildly, from 104 volts to 140 or so on the LCD. I checked the panel with a voltmeter with the same result. My batteries are 100%. If I disconnect the solar input and run on batteries only the voltage...