IRMartini
New Member
No Worries, maybe they will add it to my inverter in a future update.
Thanks
Ian
Thanks
Ian
That's what the wife keeps telling meHowever the problem in your logic
That's what the wife keeps telling me
Hi @gtdmogapiGoodday,
I am new to this forum, need help with settings of my Luxpowertek SNA5000 inverter and powerporter lithium battery. Currently set to lead-acid.
Does the inverter show your small export? or are you seeing this export from your Grid meter?Can someone tell me why the 12K sends back to the grid .1kw every couple of days? All settings (that i know of are off).
If anyone is interested here is a little documentation on this feature I got from LuxPower.@Eddie_LuxPowerTek
Just noticed a new section has appeared in my lux settings this week 'Battery Calibration'
View attachment 203444
Can you explain what it does (obviously calibrates the battery but how) and recommended settings to start with.
Many Thanks
Ian
On the inverter.... when originally posted the reading was 2.7...now 3.5kw.. I will try the offset; thanksDoes the inverter show your small export? or are you seeing this export from your Grid meter?
I noticed my system was exporting a small amount when my inverters were showing no export at all and it was down to the CT Power offset
View attachment 204822
My installers had it set at positive 60 and I've found the correct value around minus 15, I did this with several weeks of trial and error. If you have the correct electrical meter I understand this offset can be measured and entered.
Also the amount your talking about is tiny that's 2 watts an hour, I don't think mine is that close now!
I don't think your going to get it any tighter than that.
On the inverter.... when originally posted the reading was 2.7...now 3.5kw.. I will try the offset; thanks
What am I missing? The minimal power is still being sent to the grid (isnt it?) if so I would think the offset will either raise or lower the number that is seen and do nothing for the power to the grid unless the ct's tell the inverter to stop thru the offset....
Hi, I hope you can help me with a problem with my Luxpower setup. I have the LXP ACS 3600 connected to 280Ah of LiFePO cells. The BMS is not compatible with Luxpower so the unit is set to "lead-acid" and has been working well for 18 months. A week ago the unit stopped charging and discharging the battery. The LCD shows fault codes 8 and 9 (parallel CAN fault and master loss). Obviously, I do not have a parallel system and there is no CAN cable or communication. The unit is showing my solar generation, house consumption and grid export correctly. I have tried turning it off for 24 hours but the fault continues. My BMS is working normally. The device number is 1052016012 running software version BAAB0808. Is there a wy to resolve this fault or reset the unit please? Many thanks.Hi friends, if you have any questions about Luxpower inverter, please post them here, we will try to reply as soon as we can.
Someone set it as a slave of your inverter thru the inverter screen, now i set it as a primary master and the code should go away.Hi, I hope you can help me with a problem with my Luxpower setup. I have the LXP ACS 3600 connected to 280Ah of LiFePO cells. The BMS is not compatible with Luxpower so the unit is set to "lead-acid" and has been working well for 18 months. A week ago the unit stopped charging and discharging the battery. The LCD shows fault codes 8 and 9 (parallel CAN fault and master loss). Obviously, I do not have a parallel system and there is no CAN cable or communication. The unit is showing my solar generation, house consumption and grid export correctly. I have tried turning it off for 24 hours but the fault continues. My BMS is working normally. The device number is 1052016012 running software version BAAB0808. Is there a wy to resolve this fault or reset the unit please? Many thanks.