Plum Crazy Rob
Solar Enthusiast
Supplyhouse.com has good prices for everything...that's where I got PEX for my place here in Colorado
Not a bad plan, I bought a little. If you dont use resale at a huge profit most likely!I'm thinking about buying a jug of r410a. All my systems have that.
With the r410a phase out at the end of 2022, I am surprised SS could sell the r410a units at all in 2023.Not a bad plan, I bought a little. If you dont use resale at a huge profit most likely!
The solaracdc.com Deye units already use R32 in Australia. Kinda wish SS was bringing those not the 410 units. R410 will go up just like R12, R22, etc. Keep in mind in a perfect world it *is* possible for HVAC to not leak - my puny 4 ton Geo Florida Heat Pump from 2002 is R22. Ironically DIY install by me - no leaks. When it finally vents should be replacement time...
I gave up trying to find the formal EPA rule, but I think the ban on using R410A in new equipment starts in 2025. So the phase-out has started but the ban isn't implement until 2025 given push-back from the HVAC industry.With the r410a phase out at the end of 2022
I haven't read the specs. But you are correct that amps must be drawn. Having more available isn't an issue. Except in a short circuit situation. So, if in doubt. Fuse it at the safe limit.I know we already visited this once with Jedi of Electrical @timselectric , but Tim or others I know you probably haven't much read the spec sheet or manual for these. Why is it so "prominently " specified max Isc is whatever?? What possible reason could there be for this??
Per Jedi Tim, current is pulled not pushed. Same as plugging your 0.1 amp alarm clock into your 20A circuit??
I believe (if I understood correctly) @timselectric said that the unit would not draw any more power then it needed, so it did not really matter if I understood correctly
But I think the issue would come in in the case of a short circuit. Which is what ISC is for the panel rating
1.AC limiter always on
Run the unit cooling mode, set low air flow, set temperature 90 F degree, 8 times “Ac limiter button” within 10 seconds then hear 4 times “Di Di Di Di” sound, then AC limiter will always on. If want to cancel, do the same again.
2.Light status can not be remembered, because light is important to let customer know the unit is working or not. Already our side canceled the Power on Di Di sound.
3.If the solar is not good, for example morning time or cloudy days, the unit will try 3 times to start itself, 1st time 15 minutes after the unit off, 2nd time 45 minutes later, 3rd time 1 hour later, if both 3 times start itself failed within this 2 hours, then it will not try again, and will show LP(Low Power) on display. It is set to protect the air conditioner system from cloudy and rainy days, and will protect the compressor.
4.Normally for the solar inverter air conditioner keep the actual room temperature only 2 F degree gap from the set temperature without unit compressor shut down. If the room actual temperature reach or very close to the setting temperature then compressor speed very low and with very few consumption, just keep the temperature no rise no drop. If the unit will shut off and temperature gap will reach 2F with the set temperature, it means the room is too small for the unit. For example if the room is 20 square meter but installed a 24K, then very fast the house will cool and even the lowest speed of compressor and cooling will cool the house to be low, then compressor will shut down if the gap reach 2F degree.
5.App Schedule function this is Auxiliary Functions, for details upgrading we need to step by step checking, temperature schedule is very good point of this unit for sure, we will check if we can improve our unit to be smarter
Holy Shmoly!!! Yourself, @Markus_SignatureSolar , and Deye are all "the men" !! How's THAT for a quick response (on all points in fact, not just Limiter)..And it appears to be good news for the AC Limiter.
I just set and confirmed thru one on/off cycle on all 3 of my units that the Limit Hack does indeed workHoly Shmoly!!! Yourself, @Markus_SignatureSolar , and Deye are all "the men" !! How's THAT for a quick response (on all points in fact, not just Limiter)..
Welcome, Don. They must be selling quite a few of these!! I am surprised at another member from KS, much less neighboring County!Rob, I'm just a little north of you, latitude-wise, in Marion County.
Yeah I thought the same, for when my Bedroom units go up. Perhaps in the future APP updates we desire can set a schedule.In some (of my) use cases, being Locked "Always On" is not problem. But in my bedroom 12k I want control of that.
I have seen a Max - ish output in watts for the 12k to be just under 1000w so far.Yeah I thought the same, for when my Bedroom units go up. Perhaps in the future APP updates we desire can set a schedule.
So for the record 300W = "12k BTU on limiter" is not enough Cooling for the bedroom or its just more complicated than that?? General all mini split question here, does anyone know is output linear BTU / Watt, or lower/higher at reduced wattages??